DSC Power632 Manual de instruções - Página 2

Procurar online ou descarregar pdf Manual de instruções para Painel de controlo DSC Power632. DSC Power632 11 páginas. Power632
Também para DSC Power632: Manual de instruções (11 páginas)

Imprimir página

WARNING

Please Read Carefully

Note to Installers

This warning contains vital information. As the only individual in contact

with system users, it is your responsibility to bring each item in this warn-

ing to the attention of the users of this system.

System Failures

This system has been carefully designed to be as effective as possible. There

are circumstances, however, involving fire, burglary, or other types of emer-

gencies where it may not provide protection. Any alarm system of any type

may be compromised deliberately or may fail to operate as expected for a

variety of reasons. Some but not all of these reasons may be:

Inadequate Installation

A security system must be installed properly in order to provide adequate

protection. Every installation should be evaluated by a security profes-

sional to ensure that all access points and areas are covered. Locks and

latches on windows and doors must be secure and operate as intended.

Windows, doors, walls, ceilings and other building materials must be of

sufficient strength and construction to provide the level of protection

expected. A reevaluation must be done during and after any construction

activity. An evaluation by the fire and/or police department is highly recom-

mended if this service is available.

Criminal Knowledge

This system contains security features which were known to be effective at

the time of manufacture. It is possible for persons with criminal intent to

develop techniques which reduce the effectiveness of these features. It is

important that a security system be reviewed periodically to ensure that its

features remain effective and that it be updated or replaced if it is found that

it does not provide the protection expected.

Access by Intruders

Intruders may enter through an unprotected access point, circumvent a

sensing device, evade detection by moving through an area of insuffi-

cient coverage, disconnect a warning device, or interfere with or pre-

vent the proper operation of the system.

Power Failure

Control units, intrusion detectors, smoke detectors and many other security

devices require an adequate power supply for proper operation. If a device

operates from batteries, it is possible for the batteries to fail. Even if the

batteries have not failed, they must be charged, in good condition and in-

stalled correctly. If a device operates only by AC power, any interruption,

however brief, will render that device inoperative while it does not have

power. Power interruptions of any length are often accompanied by voltage

fluctuations which may damage electronic equipment such as a security sys-

tem. After a power interruption has occurred, immediately conduct a com-

plete system test to ensure that the system operates as intended.

Failure of Replaceable Batteries

This system's wireless transmitters have been designed to provide several

years of battery life under normal conditions. The expected battery life is a

function of the device environment, usage and type. Ambient conditions

such as high humidity, high or low temperatures, or large temperature fluc-

tuations may reduce the expected battery life. While each transmitting de-

vice has a low battery monitor which identifies when the batteries need to

be replaced, this monitor may fail to operate as expected. Regular testing and

maintenance will keep the system in good operating condition.

Compromise of Radio Frequency (Wireless) Devices

Signals may not reach the receiver under all circumstances which could

include metal objects placed on or near the radio path or deliberate

jamming or other inadvertent radio signal interference.

System Users

A user may not be able to operate a panic or emergency switch possibly due

to permanent or temporary physical disability, inability to reach the device

in time, or unfamiliarity with the correct operation. It is important that all

system users be trained in the correct operation of the alarm system and that

they know how to respond when the system indicates an alarm.

Smoke Detectors

Smoke detectors that are a part of this system may not properly alert occupants of

a fire for a number of reasons, some of which follow. The smoke detectors may have

been improperly installed or positioned. Smoke may not be able to reach the

smoke detectors, such as when the fire is in a chimney, walls or roofs, or on the

other side of closed doors. Smoke detectors may not detect smoke from fires on

another level of the residence or building.

Every fire is different in the amount of smoke produced and the rate of burning.

Smoke detectors cannot sense all types of fires equally well. Smoke detectors may

not provide timely warning of fires caused by carelessness or safety hazards such

as smoking in bed, violent explosions, escaping gas, improper storage of flam-

mable materials, overloaded electrical circuits, children playing with matches or

arson.

Even if the smoke detector operates as intended, there may be circumstances when

there is insufficient warning to allow all occupants to escape in time to avoid

injury or death.

Motion Detectors

Motion detectors can only detect motion within the designated areas as shown

in their respective installation instructions. They cannot discriminate between

intruders and intended occupants. Motion detectors do not provide volumetric

area protection. They have multiple beams of detection and motion can only be

detected in unobstructed areas covered by these beams. They cannot detect

motion which occurs behind walls, ceilings, floor, closed doors, glass partitions,

glass doors or windows. Any type of tampering whether intentional or unin-

tentional such as masking, painting, or spraying of any material on the lenses,

mirrors, windows or any other part of the detection system will impair its proper

operation.

Passive infrared motion detectors operate by sensing changes in temperature.

However their effectiveness can be reduced when the ambient temperature rises

near or above body temperature or if there are intentional or unintentional sources

of heat in or near the detection area. Some of these heat sources could be heaters,

radiators, stoves, barbeques, fireplaces, sunlight, steam vents, lighting and so

on.

Warning Devices

Warning devices such as sirens, bells, horns, or strobes may not warn

people or waken someone sleeping if there is an intervening wall or door.

If warning devices are located on a different level of the residence or premise,

then it is less likely that the occupants will be alerted or awakened. Au-

dible warning devices may be interfered with by other noise sources such

as stereos, radios, televisions, air conditioners or other appliances, or

passing traffic. Audible warning devices, however loud, may not be heard

by a hearing-impaired person.

Telephone Lines

If telephone lines are used to transmit alarms, they may be out of service or busy

for certain periods of time. Also an intruder may cut the telephone line or defeat

its operation by more sophisticated means which may be difficult to detect.

Insufficient Time

There may be circumstances when the system will operate as intended, yet the

occupants will not be protected from the emergency due to their inability to

respond to the warnings in a timely manner. If the system is monitored, the

response may not occur in time to protect the occupants or their belongings.

Component Failure

Although every effort has been made to make this system as reliable as possible,

the system may fail to function as intended due to the failure of a component.

Inadequate Testing

Most problems that would prevent an alarm system from operating as in-

tended can be found by regular testing and maintenance. The complete sys-

tem should be tested weekly and immediately after a break-in, an attempted

break-in, a fire, a storm, an earthquake, an accident, or any kind of construc-

tion activity inside or outside the premises. The testing should include all

sensing devices, keypads, consoles, alarm indicating devices and any other

operational devices that are part of the system.

Security and Insurance

Regardless of its capabilities, an alarm system is not a substitute for prop-

erty or life insurance. An alarm system also is not a substitute for property

owners, renters, or other occupants to act prudently to prevent or mini-

mize the harmful effects of an emergency situation.

LIMITED WARRANTY

Digital Security Controls Ltd. warrants the original purchaser that

for a period of twelve months from the date of purchase, the product

shall be free of defects in materials and workmanship under normal

use. During the warranty period, Digital Security Controls Ltd.

shall, at its option, repair or replace any defective product upon

return of the product to its factory, at no charge for labour and

materials. Any replacement and/or repaired parts are warranted for

the remainder of the original warranty or ninety (90) days, whichever

is longer. The original purchaser must promptly notify Digital

Security Controls Ltd. in writing that there is defect in material or

workmanship, such written notice to be received in all events prior

to expiration of the warranty period. There is absolutely no warranty

on software and all software products are sold as a user license under

the terms of the software license agreement included with the product.

The Customer assumes all responsibility for the proper selection,

installation, operation and maintenance of any products purchased

from DSC. Custom products are only warranted to the extent that

they do not function upon delivery. In such cases, DSC can replace

or credit at its option.

International Warranty

The warranty for international customers is the same as for any

customer within Canada and the United States, with the exception

that Digital Security Controls Ltd. shall not be responsible for any

customs fees, taxes, or VAT that may be due.

Warranty Procedure

To obtain service under this warranty, please return the item(s) in

question to the point of purchase. All authorized distributors and

dealers have a warranty program. Anyone returning goods to Digi-

tal Security Controls Ltd. must first obtain an authorization num-

ber. Digital Security Controls Ltd. will not accept any shipment

whatsoever for which prior authorization has not been obtained.

Conditions to Void Warranty

This warranty applies only to defects in parts and workmanship

relating to normal use. It does not cover:

• damage incurred in shipping or handling;

• damage caused by disaster such as fire, flood, wind, earthquake or

lightning;

• damage due to causes beyond the control of Digital Security Controls

Ltd. such as excessive voltage, mechanical shock or water damage;

• damage caused by unauthorized attachment, alterations, modifications

or foreign objects;

• damage caused by peripherals (unless such peripherals were supplied

by Digital Security Controls Ltd.);

• defects caused by failure to provide a suitable installation environment

for the products;

• damage caused by use of the products for purposes other than those for

which it was designed;

• damage from improper maintenance;

• damage arising out of any other abuse, mishandling or improper

application of the products.

Items Not Covered by Warranty

In addition to the items which void the Warranty, the following

items shall not be covered by Warranty: (i) freight cost to the repair

centre; (ii) products which are not identified with DSC's product

label and lot number or serial number; (iii) products disassembled

or repaired in such a manner as to adversely affect performance or

prevent adequate inspection or testing to verify any warranty claim.

Access cards or tags returned for replacement under warranty will be

credited or replaced at DSC's option. Products not covered by this

warranty, or otherwise out of warranty due to age, misuse, or damage

shall be evaluated, and a repair estimate shall be provided. No repair

work will be performed until a valid purchase order is received from

the Customer and a Return Merchandise Authorisation number (RMA)

is issued by DSC's Customer Service.

Digital Security Controls Ltd.'s liability for failure to repair the product

under this warranty after a reasonable number of attempts will be limited

to a replacement of the product, as the exclusive remedy for breach of

warranty. Under no circumstances shall Digital Security Controls Ltd.

be liable for any special, incidental, or consequential damages based

upon breach of warranty, breach of contract, negligence, strict liability,

or any other legal theory. Such damages include, but are not limited to,

loss of profits, loss of the product or any associated equipment, cost of

capital, cost of substitute or replacement equipment, facilities or services,

down time, purchaser's time, the claims of third parties, including

customers, and injury to property. The laws of some jurisdictions limit

or do not allow the disclaimer of consequential damages. If the laws of

such a jurisdiction apply to any claim by or against DSC, the limitations

and disclaimers contained here shall be to the greatest extent permitted

by law. Some states do not allow the exclusion or limitation of incidental

or consequential damages, so that the above may not apply to you.

Disclaimer of Warranties

This warranty contains the entire warranty and shall be in lieu of

any and all other warranties, whether expressed or implied (includ-

ing all implied warranties of merchantability or fitness for a particu-

lar purpose) and of all other obligations or liabilities on the part of

Digital Security Controls Ltd. Digital Security Controls Ltd. neither

assumes responsibility for nor authorizes any other person purport-

ing to act on its behalf to modify or to change this warranty, nor to

assume for it any other warranty or liability concerning this product.

This disclaimer of warranties and limited warranty are governed

by the laws of the province of Ontario, Canada.

WARNING: Digital Security Controls Ltd. recommends that

the entire system be completely tested on a regular basis. How-

ever, despite frequent testing, and due to, but not limited to,

criminal tampering or electrical disruption, it is possible for

this product to fail to perform as expected.

Out of Warranty Repairs

Digital Security Controls Ltd. will at its option repair or replace out-of-

warranty products which are returned to its factory according to the

following conditions. Anyone returning goods to Digital Security Con-

trols Ltd. must first obtain an authorization number. Digital Security

Controls Ltd. will not accept any shipment whatsoever for which prior

authorization has not been obtained.

Products which Digital Security Controls Ltd. determines to be re-

pairable will be repaired and returned. A set fee which Digital Security

Controls Ltd. has predetermined and which may be revised from time

to time, will be charged for each unit repaired.

Products which Digital Security Controls Ltd. determines not to be

repairable will be replaced by the nearest equivalent product avail-

able at that time. The current market price of the replacement prod-

uct will be charged for each replacement unit.