DSC WS4916 Series Manual de instruções de instalação e funcionamento - Página 2
Procurar online ou descarregar pdf Manual de instruções de instalação e funcionamento para Alarme de fumo DSC WS4916 Series. DSC WS4916 Series 9 páginas. Wireless smoke deteçtér
Também para DSC WS4916 Series: Instruções de instalação e de utilização (4 páginas), Manual de Instruções de Instalação e Operação (8 páginas), Manual de instruções de instalação e funcionamento (8 páginas), Manual do utilizador e instruções de instalação (17 páginas), Manual de instruções de instalação e funcionamento (8 páginas)
Imprimir página
2. Mount Smoke Detector Backplate
Secure backplate to the mounting surface using the screws pro-
vided.
Locking
Tab
Mounting Holes
CAUTION: The dust cover protects the unit when not in service.
Remove the dust cover before use.
3. Install Batteries
Insert
Last
If batteries are not installed, install batteries in the sequence indi-
cated. Use only approved Panasonic CR123A, Sanyo CR123A or
Duracell DL123A batteries. If batteries are installed, remove the
'Pull' tab to activate.
CAUTION: Without batteries the unit cannot be mounted onto
the base plate properly! (WS4916AUS version only).
4. Mounting
• Detector Installation: Position the detector on to the base plate
using the detector and base plate alignment marks. Press the
detector gently in place while rotating the detector clockwise
until the detector snaps into place. Remove the side tab from the
locking tab to lock in place (optional).
Mounting
Alignment
Marks
• Removal: Depress tab with a small slotted screwdriver. Rotate
detector counter-clockwise until the alignment marks line up.
Remove detector.
3V CR123A
3V CR123A
Insert
First
PULL
DOWN
Tab
Surface
Backplate
Tabs
Detector
CLOSE
OPEN
Installer Compensation Reset
Cleaning or replacement of the smoke sensor chamber changes
the background signal/noise of the detector; this requires the
drift compensation be reset. Compensation trouble is one of the
faults indicated when the LED indicator is OFF while the sounder
is chirping.
1. Remove batteries, then short the detector battery contacts for 5
seconds to power down unit.
2.Replace batteries to power up unit while pressing the test but-
ton.
3.The tamper switch must not be pressed.
4.The LED will flash when 5 seconds has elapsed. Release the test
button within 2 seconds of the LED flash.
5.The LED will flash every 2 seconds for 1 minute. During this
period, the detector must be mounted.
Allow an additional 2 minutes for the detector to make
background level checks.
6.Test the detector to verify normal operation.
5. Test Unit
NOTE: The central monitoring station (if used) should be notified
prior to the test being generated. This will prevent a false alarm
and an unnecessary response from the central monitoring sta-
tion.
Initiate test by pressing the test button for 5 seconds minimum.
Alarm activation is indicated by the flashing LED, the sounder,
and transmission of the alarm signal to the control panel. The
detector restores to normal when the test button is released.
NOTE: Allow a minimum of 20 seconds after power up and ,
after test, alarm or tamper restore activations. Do not use test
button when smoke is present.
NOTE: If the detector is in one of the following states when a
test is initiated; it will not enter an alarm state.
• Tamper, (detector not installed on mounting plate)
• Compensation Trouble
• Other internal faults that could prevent a smoke or heat alarm.
NOTE: Smoke sensitivity of installed detectors can be measured
without removal or an alarm being generated using the FSD-100
Smoke Detector Test Meter.
To test the unit using the FSD-100, set the test meter up to read
devices as per the instructions supplied. Depress the test button
on the smoke detector for 1 second and release.
NOTE: If the test button is held for 5 seconds or longer, an alarm
will be generated.
Move the test meter over the center of the detector, wait until
you hear the test meter beep, remove the unit and the informa-
tion can be immediately reviewed. Please see the instructions
supplied with the FSD-100 Smoke Detector Test Meter for more
information.
6. Device Enrollment
The 6 digit serial number located on the back of the smoke
detector housing must be enrolled into the alarm control panel
with Installer programming. Refer to the receiver Installation
Manual for details. For placement tests remove detector from
backplate for one second (tamper) then reattach. Wait at least 30
seconds for test result before activating again.
Owners Instructions
Fire Safety In The Home
Most fires occur in the home, and to minimize this danger, it is
recommended that a household fire safety audit be conducted
and a family escape plan be developed.
Household Fire Safety Audit
1. Are all electrical appliances and outlets in safe condition? Check
for frayed cords, overloaded lighting circuits, etc. If you are
uncertain about the condition of your electrical appliances or
household service, have a professional evaluation.
2.Are all flammable liquids safely stored in closed containers, and
in a cool and well ventilated area? Cleaning the unit with flam-
mable liquids should be avoided.
3.Are hazardous materials (i.e. matches) out of the reach of chil-
dren?
4.Are furnaces and wood burning appliances properly installed,
clean, and in good working order? If in doubt, have a profes-
sional evaluation.