Anywire ASLINKAMP LA-A1AW Manual do produto
Procurar online ou descarregar pdf Manual do produto para Terminais tácteis Anywire ASLINKAMP LA-A1AW. Anywire ASLINKAMP LA-A1AW 12 páginas. Anywireaslink system, analog input unit ch insulated type with 7-segment
AnyWireASLINK System Products Guide
ASLINKAMP
[Analog Input Unit (CH insulated type with 7-segment)]
L□-A1AW
[Notes on Safety]
Precautions that must be observed in order to use this system safely are
indicated as shown below. You must observe these precautions.
A WARNING indicates a potentially hazardous situation which, if not
WARNING
!
handled correctly, could result in death or serious injury.
A CAUTION indicates a potentially hazardous situation which, if not
CAUTION
!
handled correctly, may result in personal injury or property damage.
○ System Safety
!
WARNING
This system is intended for general industrial applications. It does not
have functions for supporting applications requiring higher levels of safety
such as safety-related devices or accident prevention systems.
○ Always turn off the system power before attempting to mount or replace.
○ Prolonged continuous ow of a rated load current or higher or a transit
current due to load short-circuit or similar problem, in the hybrid unit
including the output unit and the output circuit may result in smoke
generation or re. An external safety device such as a fuse must be
installed.
○ System power supply
!
CAUTION
Use a stabilized 24V DC power supply. Use of a non-stabilized power
supply may cause problems with the system.
○ Separately route high-voltage and power cables
Although the AnyWireASLINK has a high noise margin, lay the
transmission lines and I/O cables so as to keep them away from
high-voltage and power cables.
○ Connectors and terminals
・ Pay careful attention to the length and installation of cable wiring to
e n s u r e t h a t c o n n e c t o r s a n d c a b l e s a r e n e i t h e r s t r e s s e d n o r
disconnected even if they are stressed.
・ Make sure to prevent any metal objects from getting inside the
connectors or the terminal blocks.
・ Short-circuits caused by metal objects or mis-wiring are likely to
damage the device.
○ Do not impose any external loads on the units.
Doing so may cause a failure.
○ Do not disconnect or reconnect between the transmission line and slave
units when a transmission line is operating.
A malfunction may occur.
○ Use the AnyWireASLINK within the range of the speci cations and
conditions shown below.
[Warranty]
■ Warranty period
The warranty on the delivered Product shall continue to be effective for one (1)
year after the delivery thereof to a location as designated by the original owner.
■ Scope of warranty
Should a defect occur in any part of the Product during the foregoing warranty
period when it is used normally in accordance with the speci cations described
in this User's Manual, the Company shall replace or repair the defect free of
charge, except when it arises as a result of:
[1] Misuse or abuse of the Product by the owner;
[2] Fault caused by cause other than the delivered Product;
[3] Unauthorized modi cation or repair of the Product by any party other than
the Company;
[4] Any unusual force of nature, disaster, or other cause beyond the Company's
control.
The term "warranty," as used herein, refers to the warranty applicable to the
delivered product alone. The Company shall not be liable for any damages
consequential or incidental to a malfunction of the delivered product.
■ Repair at cost
After the expiration of the warranty period, any troubleshooting or repairs shall
be done at the expense of the owner.
Even during the warranty term, any repairs and troubleshooting for defects
arising from causes outside the scope of the warranty as speci ed above shall
be done at the owner's expense.
[Type]
Bit operation
Analog input unit
LA-A1AW
(CH insulated type
LB-A1AW
with 7-segment)
1CH (Base unit)
1CH (Extension unit)
-L*A1AW 1/11-
[Function]
Model
ASLINKAMP
CH insulated
Insulated
Measurement
Voltage: 0-10V, 0-5V, 1-5V
input range
Current: 4-20 mA, 0-20 mA
Resolution
1/16000
Input speci cations setting
Reference point shift mode
Functions
Average number of moving times
Address/parameter automatic setting (Base unit only)
Miniature
[Included items]
LA-A1AW (Base)
LB-A1AW (Extension)
[Name of each part]
7-segment display
Analog port
e-CON (3P)
7-segment display
Analog port
e-CON (3P)
Base unit ...1
Base unit ...1
Protective cover
Base
LED display
Transmission line
Extension
Protective cover
LED display
Expansion connector