Apollo Xpander XPA-14017-APO Manual de colocação em funcionamento - Página 3
Procurar online ou descarregar pdf Manual de colocação em funcionamento para Sensores de segurança Apollo Xpander XPA-14017-APO. Apollo Xpander XPA-14017-APO 14 páginas.
Imprimir página
Battery monitoring
Devices in the XPander range are powered by batteries.
There are two battery packs with current being drawn
alternatively from each. It is essential that the state of
the batteries is known and therefore the three states
that follow have been defined:
Normal
Batteries in good working order
Fault*
Batteries need to be changed
Missing** Battery voltage very low or battery pack
incorrectly fitted
* For the 'Fault' state a warning is sent 30 days before
battery failure.
** For the 'Missing' state a warning is sent seven days
before battery failure.
When changing the batteries, both packs within the
device should be changed at the same time.
Battery life is typically between three and five years
but Apollo can only guarantee this if the recommended
replacement alkaline batteries are used. It is
recommended that the batteries are changed during
the year four maintenance period.
Batteries should be disposed of in accordance with
local regulations.
Handling
As with all electronics, care should be taken during
handling. Avoid dropping any of the parts onto hard
surfaces as damage may occur to the device case and
internal circuitry.
To minimise the risk of damage all products should be
kept in their packaging until they are installed. Retain
all packaging until the installation and commissioning
is complete.
Observe anti-static precautions when handling all
products. To avoid the risk of static discharge do not
place sensitive devices on plastic surfaces.
All packaging is recyclable.
XPander product range
All XPander detectors are supplied as complete units
with a mounting base. The range is made up of the
products that follow:
Product
Heat Detector A1R with base
Part No.
XPA-CB-11170-APO
Product
Heat Detector CS with base
Part No.
XPA-CB-11171-APO
Product
Optical Smoke Detector with base
Part No.
XPA-12034-APO
Product
Red sounder with mounting base
Part No.
XPA-CB-14001-APO
Product
White sounder with mounting base
Part No.
XPA-CB-14002-APO
Product
Red sounder visual indicator with red mounting
base
Part No.
XPA-CB-14003-APO
Product
Amber sounder visual indicator with white
mounting base
Part No.
XPA-CB-14004-APO
Product
Clear sounder visual indicator with white
mounting base
Part No.
XPA-CB-14005-APO
Product
Combined sounder and optical smoke detector
Part No.
XPA-CB-14016-APO
Product
Combined sounder and A1R heat detector
Part No.
XPA-14017-APO
Product
Combined sounder and CS heat detector
Part No.
XPA-CB-14018-APO
Product
Combined sounder visual indicator (red) with
optical smoke detector
Part No.
XPA-CB-14020-APO
Product
Combined sounder visual indicator (red) with
A1R heat detector
Part No.
XPA-CB-14021-APO
Product
Combined sounder visual indicator (red) with
CS heat detector
Part No.
XPA-CB-14022-APO
Product
Combined sounder visual indicator (clear) with
optical smoke detector
Part No.
XPA-CB-14024-APO
Product
Combined sounder visual indicator (clear) with
A1R heat detector
Part No.
XPA-CB-14025-APO
Product
Combined sounder visual indicator (clear) with
CS heat detector
Part No.
XPA-CB-14026-APO
Product
Single input/output unit
Part No.
XPA-IN-14011-APO
Product
Dual input/output unit
Part No.
XPA-IN-14012-APO
Product
Diversity loop interface
Part No.
XPA-IN-14050-APO
Product
Remote indicator module
Part No.
XPA-IN-14102-APO
Product
Manual call point
Part No.
XPA-MC-14006-APO
Product
Site Survey Kit
Part No.
XPA-TE-14075-APO
Product
Red XPander XPERT card
Part No.
29600-399
Product
White XPander XPERT card
Part No.
29600-413
PP2286/2019/Issue 13
Page 2 of 12