AUSUM ML-CS37-36 Manual de montagem, utilização e manutenção - Página 6

Procurar online ou descarregar pdf Manual de montagem, utilização e manutenção para Chave de fendas eléctrica AUSUM ML-CS37-36. AUSUM ML-CS37-36 12 páginas.

Imprimir página
FR
5) Battery tool use and care
a) Recharge only with the charger specified by the manufacturer.
ES
when used with another battery pack.
b) Use power tools only with specifically designated battery packs.
PT
c) When battery pack is not in use, keep it away from other metal objects, like paper clips, coins, keys, nails, screws or other small
metal objects, that can make a connection from one terminal to another.
d) Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact accidentally occurs, flush with water. If
IT
liquid contacts eyes, additionally seek medical help.
6) Service
EL
a) Have your power tool serviced by a qualified repair person using only identical replacement parts.
power tool is maintained.
2 、 EXTRA SAFETY REGULATIONS CONCERNING CORDLESS SCREWDRIVER
PL
Hold power tool by insulated gripping surfaces, when performing an operation where the fastener may contact hidden wiring.
Fasteners contacting a "live" wire may make exposed metal parts of the power tool "live" and could give the operator an electric shock.
RU
If possible, always use clamps or a vice to hold your work.
Always switch o before you put the tool down.
Ensure that the lighting is adequate.
UA
Do not put pressure on the tool, such that it slows the motor down. Allow the bit to screw without pressure. You will get better results and you will be
taking better care of your tool.
Keep the area free of tripping hazards.
RO
Only use accessory bits in good condition.
Before starting, check that there is su cient clearance for the bit under the workpiece.
Do not touch the bit away after operation. It will be very hot.
EN
Keep your hands away from under the workpiece.
Never use your hands to remove dust, chips or waste close by the bit.
Rags,cloths,cord,string and the like should never be left around the work area.
Support the workpiece properly.
If you are interrupted when operating the tool, complete the process and switch o before looking up.
Periodically check that all nuts, bolts and other xings are properly tightened.
When using the tool, use safety equipment including safety glasses or shield. Hearing protection, and protective clothing including safety gloves.
Wear a dust mask if the operation creates dust.
3、BATTERY AND CHARGING SAFETY WARNINGS
Make sure the USB cord is located so that it will not be stepped on, tripped over, or otherwise subjected to damage or stress.
Do not store or use the tool in locations where the temperature may reach or exceed 40℃(such as inside sheds or metal buildings in summer).
The tool is not fully charged out of the carton. First read the safety instructions and then follow the charging notes and procedures.
The longest life and best performance can be obtained if the tool is charged when the air temperature is between 18-24℃. Do not charge the tool
in an air temperature below 10℃ or above 40℃. This is important and will prevent damage to the tool.
Do not incinerate the tool even if it is seriously damaged or is completely worn out. The battery can explode in a re.
Never attempt to open the tool for any reason. If the plastic housing of the tool breaks or cracks, immediately discontinue use and do not recharge.
During charging, the tool must be placed in a well ventilated area.
The battery utilizes lithium cells. Lithium is considered to be a toxic material. Use an environmentally safe disposal until at a municipal waste disposal
centre to dispose of a damaged or worn out battery.
4、EXTRA SAFETY REGULATIONS CONCERNING ELECTRONIC TORCH FUNCTION
To reduce the risk of injury, close supervision is necessary when the ashlight function is used near children.
Do not stare at light source.
Do not place or store appliance where it can fall or be pulled into a tub or sink.
Recharge when the brightness goes lower for prolonging battery life.
The torch LED don't allowed to change.
A charger that is suitable for one type of battery pack may create a risk of re
Use of any other battery packs may create a risk of injury and re.
Shorting the battery terminals together may cause burns or a re.
Liquid ejected from the battery may cause irritation or burns.
3
This will ensure that the safety of the