ADEMCO 5850 Instruções de instalação - Página 4
Procurar online ou descarregar pdf Instruções de instalação para Sensores de segurança ADEMCO 5850. ADEMCO 5850 5 páginas. Glass break detector/transmitter
Imprimir página
MOUNTING
1. Determine the optimum mounting location, noting the following:
• Mount on the ceiling or on a wall at least 7 feet from the floor.
• Mount such that the detector has a direct, unobstructed line-of-
sight to the protected glass.
• Mount no more than 25 feet from the farthest protected glass.
• Make sure there are no intervening partitions, curtains, etc. that
could block the transfer of shock or sound waves.
Note: If window dressing is present it will absorb sound energy
from breaking glass. In such cases, the detector should be
mounted between the protected glass and the window dressing.
• Avoid locating the detector near sources of ambient vibration or
sound, such as: air conditioners, fans, blowers, air ducts, or
loudspeakers
• Avoid locations where furniture can be moved so that it blocks
the detector's line-of sight to the glass.
• Avoid locations where a door can be open or closed such that it blocks the detector's line-of sight to the glass.
• Avoid locations near doors or windows that may be slammed.
2. Before mounting the 5850 permanently, conduct Go/No Go tests (see control's instructions) to verify adequate
signal strength, and reorient or relocate the 5850 if necessary (press the detector's test switch to send a
transmission). It is also recommended that before mounting permanently the detector be tested to ensure it is
within reliable audio and flex range from the protected glass. See the Testing Alarm Operation section for the
procedure.
3. If not already removed, remove the detector's cover assembly by removing the screw located near the LED
ENABLE switch. Carefully pull the cover assembly away from the case.
4. Mark the mounting hole locations on the ceiling or wall using the case as a template.
5. Drill holes (if necessary) and insert mounting screws part way into the ceiling or wall (use anchors if necessary).
6. Hang the narrow part of the case mounting slots over the screws and tighten securely.
TESTING ALARM OPERATION
To test the operation of the 5850, use the Intellisense model FG-700 Glass Break Simulator.
Before proceeding, open the cover door and slide the LED ENABLE switch in the direction of the arrow.
1. Test the audio range as follows:
a. Activate the simulator in manual mode at the farthest point of the glass being protected (maximum 25 feet).
b. Observe that the green audio LED flashes.
2. Test the flex range as follows:
a. Carefully strike the protected glass with your hand or a cushioned tool.
b. Observe that the yellow flex LED flashes.
c. Set the simulator to flex mode.
d. Arm the simulator by pressing the red button.
e. Generate a flex signal by carefully striking the protected glass within 30 seconds of arming the simulator. The
simulator will automatically create the sound of breaking glass.
f. Observe that the red alarm LED flashes, indicating an alarm condition.
3. To ensure maximum protection against false alarms, activate all equipment in the vicinity. None of the detector's
LEDs should flash.
4. After testing, disable the LEDs (if desired) by pushing the orange tab gently back into the detector case.
MAINTAINING PROPER OPERATION
To maintain the detector in proper working condition, it is important that use observe the following:
1. Replace the battery when the system indicates that the 5850 has reported a low battery condition.
2. Units should never be relocated without the advice or assistance of the alarm service company.
3. Fans, air conditioners, blowers, loudspeakers, or other sources of vibration and sound should not be introduced
into the protected area after installation of the detectors. If this is unavoidable, the alarm service company should
be notified and a readjustment/re-test of the system performed.
www.PDF-Zoo.com
5850 Mounted
on ceiling
5850 Mounted on
any wall (top view)
--- 3 ---