Automationdirect.com Stride SE3-SW5U-N67-T Manual - Página 2

Procurar online ou descarregar pdf Manual para Interruptor Automationdirect.com Stride SE3-SW5U-N67-T. Automationdirect.com Stride SE3-SW5U-N67-T 2 páginas. Ip67 rated industrial unmanaged ethernet switches

Imprimir página
6.1
16.1
Dimensions:
.64
0.64
mm [inches]
12.8
0.50
47.8
1.88
37.2
1.46
Installation – Panel Mounting:
The switch is designed to be panel mounted vertically
MANAGED ETHERNET SWITCH, 5 PORTS, (5) ETHERNET 10/100Base-T
+75 DEG C, PLASTIC HOUSING, IP67, 35mm DIN RAIL OR PANEL MOUNT
or horizontally using the steps below.
O
S MAY DIFFER SLIGHTLY
PART DIMENSIONS MAY DIFFER SLIGHTLY
TURER'S VARIANCES
DUE TO MANUFACTURER'S VARIANCES
Panel mounting steps:
1. Prepare 2 screws for mounting the switch to a wall.
(M3 or M4 screws are recommended.)
2. Locate two screw holes in the wall or panel based
on the positions of two screw holes on the mount-
ing brackets.
3. Insert the screws through the screw holes on the
switch and secure the switch to the panel.
Installation – DIN Rail Mounting:
Using the included DIN rail mounting bracket, the switch
can be snapped onto a standard 35 x 7.5 mm height DIN rail
(Standard: CENELEC EN50022)
To install the DIN rail mounting bracket, use
the included screws as shown in the figure
to the right.
After the DIN-Rail bracket is installed on the
rear of the switch, follow the steps below to
mount the switch:
1. Hook top back of unit over the DIN rail.
2. Push bottom back onto the DIN rail until
it snaps into place.
3. Check to ensure that the bracket is
mounted tightly to the rail.
To remove the switch from the DIN rail, push the unit down to free the
bracket from the bottom of the DIN rail, then reverse the above steps.
Copyright 2023, AutomationDirect.com Incorporated/All Rights Reserved Worldwide
12.3
0.48
12.8
0.50
47.8
35.0
1.88
1.38
Unit weight: 0.4 kg [0.88 lb]
SE3-SW5U-N67-T
INCH UNITS USED FOR
INCH UNITS USED FOR
PART DESIGN
PART DESIGN
12.3
191.2
0.48
7.53
158.9
6.26
35.0
1.38
Power Wiring:
The switch can be powered from the same DC source that is used to power
SE3-SW5U-N67-T
your other devices. To maintain the UL listing, this source must be a Class 2
power supply. A DC voltage in the range of 12–48 VDC needs to be applied
UNLESS OTHERWISE
UNLESS OTHERWISE
mm
through an M12 connector as shown in the chart below. We recommend
SPECIFIED UNITS ARE:
SPECIFIED UNITS ARE:
[inch]
grounding the switch to the panel or chassis ground using an M3 or M4 ground
screw and grounding wire, attached to either the top or bottom wall mounting
hole. To reduce down time resulting from power loss, the switch can be
powered redundantly with a second power supply as shown in the chart below.
A recommended DC power supply is AutomationDirect.com part number
PSL-24-030.
1
4
Recommended Wire Size 24 – 18 AWG
Communication Ports Wiring:
Additional Help and Support
• For additional product support, specifications, and
installation, download User Manual SE3-USER-M from the
Product Manuals area of www.AutomationDirect.com.
• For additional technical support and questions, call our
Technical Support team @ 770-844-4200.
2
191.2
7.53
158.9
6.26
AutomationDirect.com
1-800-633-0405
LATEST VERSION
mm
8/14/2023
[inch]
Power Port Pin Definitions
Pin
2
2
1
1
3
3
2
4
5
5
3
4
5
Communication Port Pin Definitions
Pin
1
2
1
2
1
4
3
4
3
2
3
4
12.3
12.3
0.48
0.48
8.8
8.8
0.35
0.35
AutomationDire
1-800-633-0
LATEST VERSION
SHEET 1 OF 1
SHEET
8/14/2023
Description
Power Input 1 +
Power Input 2 +
Power Input 2 -
Power Input 1 -
Ground
MDI Signal
Transmit Data + (TD+)
Receive Data + (RD+)
Transmit Data - (TD-)
Receive Data - (RD-)