Garmin VHF 110 AIS series Instruções de instalação - Página 2

Procurar online ou descarregar pdf Instruções de instalação para Rádio marítimo Garmin VHF 110 AIS series. Garmin VHF 110 AIS series 4 páginas.

Imprimir página

After the device fits correctly in the cutout, ensure the mounting holes on

the device line up with the pilot holes on the template.

If the mounting holes on the device do not line up, mark the new pilot-hole

locations.

Using a 3.5 mm (

in.) drill bit, drill the pilot holes.

Remove the template from the mounting surface.

If you will not have access to the back of the device after you mount it,

connect all necessary cables to the device before placing it into the cutout.

If necessary, cover unused connectors with the attached weather caps to

prevent corrosion of the metal contacts.

Install the foam gasket

on the back of the device.

The pieces of the rubber gasket have adhesive on the back. Make sure

you remove the protective liner before installing them on the device.

Place the device in the cutout.

Secure the device to the mounting surface using the included screws

Install the decorative bezel by snapping it in place around the edges of the

device.

Mounting the Microphone Hanger

NOTICE

If you are mounting the bracket on fiberglass with screws, it is recommended

to use a countersink bit to drill a clearance counterbore through only the top

gel-coat layer. This will help to avoid cracking in the gel-coat layer when the

screws are tightened.

Stainless-steel screws may bind when screwed into fiberglass and

overtightened. It is recommended to apply an anti-seize lubricant on the

screws before installing them.

You can mount the microphone hanger in a convenient location near the radio.

Select a mounting location for the microphone within reach of the

microphone cable.

Using the microphone hanger

as a template, mark the pilot holes.

Drill the mounting holes using a 3 mm (

Secure the microphone hanger to the mounting surface using the included

screws

Connection Considerations

in.) drill bit.

Item Description

Notes

Ground

You can use the included grounding screw to connect the

connection

device chassis to water ground, if needed (Additional

Grounding Considerations, page 2).

Power, NMEA

You must connect the device to a 12 Vdc power source

0183, and

(Connecting the Wiring Harness to Power, page 2).

speaker wiring

You can connect this device to a NMEA 0183 device using

harnesses

this wiring harness to share DSC and GPS information

(optional) (NMEA 0183 Device Connections, page 3).

You can connect this device to a hailer horn using this wiring

harness (optional) (Connecting to a Hailer Horn or PA

Speaker, page 3).

You can connect this device to an external speaker using this

wiring harness (optional) (Connecting to an External Speaker,

page 3).

VHF antenna

You must connect the device to a VHF antenna (sold

connection

separately) (Connecting a VHF Antenna, page 2).

Additional

You can add an additional microphone (sold separately) or

microphone

relocate the existing microphone on a VHF 210 AIS radio

connector

(microphone relocation kit sold separately).

This connector is not available on a VHF 110 radio.

NMEA 2000

You can connect this device to a NMEA 2000 network on your

connector

boat to share DSC and GPS information (optional) (NMEA

2000 Device Connections, page 2).

Connecting the Wiring Harness to Power

Route the wiring harness to the power source and to the device.

Connect the red wire to the positive (+) battery terminal, and connect the

black wire to the negative (-) battery terminal.

Additional Grounding Considerations

This device should not need any additional chassis grounding in most

installation situations. If interference is experienced, the grounding screw on

the housing can be used to connect the device to the water ground of the boat

to help avoid the interference.

Connecting a VHF Antenna

Mount the VHF antenna (sold separately) according to the installation

instructions provided with the antenna.

Connect the VHF antenna to the antenna port on the back of the radio.

NMEA 2000 Device Connections

NOTICE

If you are connecting this device to an existing NMEA 2000 network, the

NMEA 2000 network should already be connected to power. Do not connect

the NMEA 2000 power cable to an existing NMEA 2000 network, because only

one power source should be connected to a NMEA 2000 network.

If you are connecting this device to an existing NMEA 2000 network or engine

network by another manufacturer, you should install a NMEA 2000 Power

Isolator (010-11580-00) between the existing network and the Garmin devices.

If you are installing a NMEA 2000 power cable, you must connect it to the boat

ignition switch or through another in-line switch. NMEA 2000 devices will drain

your battery if the NMEA 2000 power cable is connected to the battery directly.

To connect this device to your existing NMEA 2000 network, you must

purchase a NMEA 2000 cable and connector.

If you are unfamiliar with NMEA 2000, you should read the "NMEA 2000

Network Fundamentals" chapter of the Technical Reference for NMEA 2000

Products. Go to www.garmin.com/manuals/VHF_110_210/.