Indesit IS5G1KMW/U Manual - Página 7

Procurar online ou descarregar pdf Manual para Fogões Indesit IS5G1KMW/U. Indesit IS5G1KMW/U 17 páginas.

Imprimir página

WARNING : This operation must be perfomed

by a qualified technician

INSTALLATION TIPS

Positioning

This unit may be installed and used only in

permanently ventilated rooms according to the British

Standards Codes Of Practice: B.S. 6172/B.S. 5440,

Par. 2 and B.S. 6891 Current Editions. The following

requirements must be observed:

a. The cooker should not be installed in a bed sitting

room with a volume of less than 20m

in a room of volume less than 5m

effective area of 100cm

in a room of volume between 5m

supplementary airvent area of 50cm2 is required,

if the volume exceeds 10m

However, if the room has a door or a window which

opens directly to the outside no air vent is required

even when the volume is between 5m

The room containing the appliance must contain

an openable window or an acceptable alternative

such as an adjustable louvre or hinged panel

opening direct to outside air.

b. During prolonged use of the appliance you may

consider it necessary to open a window to the

outside to improve ventilation.

c. If there are other fuel burning appliances in the

same room, B.S.5440 Part 2 Current Edition, should,

be consulted to determine the requisite air vent.

The height of the cooker can be adjusted by means

of adjustable feet in the plinth (900mm - 915mm).

Adjust the feet by tilting the cooker from the side.

Then install the product into position.

The appliance must not be installed behind

a decorative door in order to avoid overheating

This appliance must not be fitted on a platform.

The cooker is designed to fit between kitchen cabinets

spaced 500mm apart. The space either side need

only be sufficient to allow withdrawal of the cooker for

servicing. It can be used with cabinets one side or

both as well as in a corner setting. It can also be used

free-standing.

Adjacent side walls which project above hob level,

must not be nearer to the cooker than 150mm or 65mm

and should be protected by heat resistant

material. Any overhanging surface or cooker hood

should not be nearer than 750mm.

a. The cooker may be located in a kitchen, a kitchen/

diner or bed sitting room, but not in a bathroom or

shower room.

b. The hoods must be installed according to the

requirements in the hood handbook.

c. The wall in contact with the back of the cooker must

be of flameproof material.

d. The cooker is fitted with a safety chain that must be

attached to a hook, secured to the wall behind the

appliance.

Gas connection

The cooker should be connected to the gas-supply

by a gas safe registered installer. During installation

of this product it is essential to fit an approved gas

tap to isolate the supply from the appliance for the

convenience of any subsequent removal or servicing.

Connection of the appliance to the gas mains or liquid

. If it is installed

an air vent of

is required, if it is installed

and 10m

no airvent is required.

and 10m

gas must be carried out according to the prescribed

regulation in force, and only after it is ascertained that it

is adaptable to the type of gas to be used. If not, follow

the instructions indicated in the paragraph headed

"Adaptation to different gas types". On some models

the gas supply can be connected on the left or on the

right, as necessary; to change the connection, reverse

the position of the hose holder with that of the cap

and replace the gasket (supplied with the appliance).

In the case of connection to liquid gas, by tank, use

pressure regulators that conform to the regulation in

force. The gas supply must be connected to the left

of the appliance. Be sure that the hose does not pass

through the rear of the cooker touching hot parts.

Make sure the supply pressure conforms

with the values shown in the table entitled

"Caracteristics of the burners and nozzles".

When the cooker is installed between cabinets

(recessed), the gas connection must be effected

by an approved flexible hose with bayonet fitting

(BS 669 Current Edition). The gas inlet for the

cookers is a threaded G 1/2 gas female fitting.

Adapting to different types of gas

It is possible to adapt the appliance to a type of gas other

than the default type (this is indicated on the rating label

on the cover).

Adapting the hob

Replacing the nozzles for the hob

burners:

1. Remove the hob grids and

slide the burners off their seats.

2. Unscrew the nozzles using a 7

mm socket spanner (see figure),

and replace them with nozzles

suited to the new type of gas(see Burner and nozzle

specifications table).

3. Replace all the components by following the above

instructions in reverse.

Adjusting the hob burners' minimum setting:

1. Turn the tap to the minimum position.

2. Remove the knob and adjust the regulatory screw,

which is positioned inside or next to the tap pin, until the

flame is small but steady.

! If the appliance is connected to a liquid gas supply, the

bypass screw must be set to a minimum.

3. While the burner is alight, quickly change the position of the

knob from minimum to maximum and vice versa several times,

checking that the flame is not extinguished.

Upon completion of adjustment, reseal using sealing

wax or an equivalent material.

! The hob burners do not require primary air adjustment.