Alemite Rolla AP650 Instruções de serviço

Procurar online ou descarregar pdf Instruções de serviço para Ferramentas Alemite Rolla AP650. Alemite Rolla AP650 2 páginas.

Imprimir página

Alemite Rolla AP650 Instruções de serviço

SERVICE INSTRUCTIONS

Description

With covers manufactured from high quality impact resistant and UV stabalised polypropylene and a positive latching mechanism that

automatically locks hose at the desired length, the new series of Rolla Reels from Alemite Lubrequip will provide you with a reliable cost

effective means of storing and retrieving hose assemblies in your workshop or garden. The reels can be floor, ceiling or wall mounted

and the detachable mounting bracket facilitates ease of reel mounting and storage (if required). Each and every reel is tested for its

ability to hold pressure and hose retraction prior to leaving the factory and stringent adherence to assembly and operation standards

guarantees you years of trouble free operation. Non snag roller guide assemblies, crimped hose ends and dependable swivels and

spring assemblies are other product features that ensure trouble free hose storage and retrieval.

Specifications

Uses

Hose Lengths

Materials

Weight

Inlet

Outlet

Installation Of Reel

For overhead ceiling mounting: install reel at least 3 metres

above the floor.

2 You will need to purchase appropriate hardware for the mounting

of your new reel.

3 The reel base has three 10.5mm (13/32) drilled holes for mounting

on a suitable flat surface. Figure 2 is a template showing the

correct location of the 3 mounting holes in the base.

4 Using the three holes in the base, mount the reel in the desired

location. Be sure to use appropriate hardware and to tighten the

reel securely to the mounting location.

5 Apply Teflon tape or pipe sealant to the outlet fitting on the Rolla

Reel hose, then attach to desired tool or nozzle. Check connection

for any leakage, also check the Rolla Reel hose for correct

operation. See operation section. If hose stop adjustment is

required, pull hose from reel and allow the reel to latch at the

desired length. Loosen hose stop bolts and slide hose stop to a

position close to the hose guide. Tighten hose stop bolts and

unlatch the reel.

Operation

1 Check your Rolla Reel for correct operation by slowly pulling out the hose.

A clicking noise will be heard every half revolution of the drum.

2 Latching mode switch, when your Rolla Reel is in free run state, pull out the

hose and allow it to retract after hearing the first, second or third click.

3 To unlatch the reel slowly pull out the hose until the clicking noise stops, and then let

the hose retract until the hose stop rests against the hose guide.

4 NOTE: To avoid damage to the Rolla Reel, always hold onto the hose while it is

rewinding. Periodically check the hose condition for wear or damage and check the

swivel fitting for leakage. Replace any worn, damaged or leaking parts.

Warning

1 Make sure incoming line pressure does not exceed the rated operating pressure for

your model hose reel.

2 Use proper eye protection when assembling and using the hose reel.

3 Use soap and water when checking for leaks.

4 Keep children away from the work area.

Head Office NSW

VIC

TEL: (02) 9939 0711

TEL: (03) 8787 8288

FAX: (02) 9939 0411

FAX: (03) 8787 8266

Visit our website at

Rolla Reels

Air and Water

AP650 – 15m of 10mmID hose. AP840 – 13m of 12mmID hose. WP840 – 18m of 12mmID hose.

Plastic covers, steel spring & Buna "N" seals

11Kgs

AP650 – 3/8"BSPT (m). AP840 – 1/2"BSPT(m). WP855 – 1/2"BSP(m)

QLD

TEL: (07) 3889 8480

FAX: (07) 3889 8490

www.alemite-lubrequip.com.au

SA/NT

TEL: (08) 8241 7111

TEL: (08) 9209 3066

FAX: (08) 8241 7011

FAX: (08) 9209 3933

Email - [email protected]

AP650/

AP840/

WP855

TAS

TEL: (03) 6343 0477

FAX: (03) 6343 0911