ARO 8426-4 Manual do operador
Procurar online ou descarregar pdf Manual do operador para Perfurar ARO 8426-4. ARO 8426-4 4 páginas.
OPERATOR'S MANUAL
SECTION
M20
MANUAL
35
INCLUDING: OPERATION, INSTALLATION & MAINTENANCE
Released:
5/68
Tool & Hoist Products
1100 SERIES
DRILLS
Revised:
8-2-93
Form:
4912
Models
8426-2, 8426-3, 8426-4,
8426-5, 8426-6
and
8426-7.
IMPORTANT: READ THIS MANUAL CAREFULLY BEFORE INSTALLING,
OPERATING OR SERVICING THIS EQUIPMENT.
OPERATING
AND SAFETY PRECAUTIONS
AIR SUPPLY REQUIREMENTS
Pneumatic tools should always be installed and used in accor-
dance with A.N.S.I. 8186.1 "Safety Code For Portable Air Tools."
For maximum operating efficiency, the following air supply specifi-
cations should be maintained
to this air tool:
CAUTION;
0
Keep hands and clothing away from rotating end of tool.
0
Wear suitable eye protection while operating tool.
l
Use tool only for purposes for which it was intended.
l
Disconnect air supply from tool before removing/installing
bits
or performing other maintenance
procedures.
WARNING
Repeated prolonged operator exposure to vibrations
which may be generated
in the use of certain hand-held
tools
may produce Raynaud's phenomenon,
commonly referred to as
Whitefinger disease. The phenomenon
produces numbness and
burning sensations
in the hand and may cause circulation
and
nerve damage
as well as tissue necrosis.
Repetitive
users of
hand-held
tools who experience
vibrations should closely moni-
tor duration of use and their physical condition.
l
AIR PRESSURE
- 90 PSIG (6 bar)
l
AIR FILTRATION - 50 micron
.
LUBRICATED
AIR SUPPLY
l
HOSE SIZE - 5/16" (8 mm) I.D.
An ARO© model 128231-800
air line FILTER/REGULATOR/LU-
BRICATOR
(F.R.L.) is recommended
to maintain the above air
supply specifications.
ROUTINE
LUBRICATION
REQUIREMENTS
Lack of or an excessive amount of lubrication will affect the perfor-
mance and life of this tool. Use only recommended
lubricants at
below time intervals:
EVERY 8 HOURS OF TOOL OPERATION-Fill
lubricator reser-
voir of recommended
F.R.L. with spindle oil (29665). If an in line or
air line lubricator is not used, apply several drops of spindle oil
(29665) in air inlet.
EVERY 160 HOURS OF TOOL OPERATION
- Flush tool with a
solution of three (3) parts cleaning solvent to one (1) part spindle
oil.
EVERY 1000 HOURS OF TOOL OPERATION
-Completely
dis-
assemble tool, clean and lubricate motor bearings with NLGI #1
"EP" grease (33153).
RECOMMENDED
LUBRICANTS
Afterdisassembly
is complete, all parts, except sealed or shielded
bearings, should be washed with solvent. To relubricate parts, or
for routine lubrication, use the following recommended
lubricants:
Where Used
ARO Part #
Description
Air Motor
29665
1 qt. Spindle Oil
"O" Rings & Lip Seals
36460
4
oz. Stringy Lubricant
Gears and Bearings
33153
5 lb. "EP" - NLGI #1 Grease
For parts and service information,
contact your local ARO distributor, or the Customer Service Dept. of the Ingersoll-Rand
Dis-
tribution Center, White House, TN at PH: (615) 672-0321,
FAX: (615) 672-0601.
ARO Tool & Hoist Products
Ingersoll-Rand
Company
1725 U.S. No. 1 North
l
P.O. Box 8000
Southern Pines, NC 2838843000
©1993
THE ARO CORPORATION.
PRINTED
IN U.S.A.
PROFESSIONALTOOLS