artisan ARTPC-SB2M Manual de instruções de montagem - Página 6
Procurar online ou descarregar pdf Manual de instruções de montagem para Acessórios para grelhadores artisan ARTPC-SB2M. artisan ARTPC-SB2M 8 páginas. Dual side burner mounting bracket for artisan cart models: artpc-26, 32 and 36
STEP 7:
Now that the 3/8" flex stainless steel gas line has been rout-
ed inside the body of the ARTP BBQ cart, it needs to be con-
nected to the BBQ main feed gas line.
WARNING:
In LP systems: Close the LP Tank Valve, disconnect the LP
tank, remove it from the cart and disconnect the LP Gas
line / Regulator assembly from the BBQ Gas Regulator.
In NG systems: Turn the Main Gas Valve off, and discon-
nect the Flexible gas line (or hard pipe) from the gas pres-
sure regulator.
The gas line connections will be made at the regulator setup
located under the ARTP BBQ in the back (right side) of the
unit.
Using an adjustable wrench or other appropriate tool, re-
move the 3/8" ODF x 1/2" NPT adapter (LP systems) or the
1/2" ODF x 1/2" NPT adapter (NG systems) from the BBQ
Gas regulator.(see figure # 7). Save the adapter fitting as it
will be reused in the next step.
It is not necessary to remove the GAS Regulator from the
ARTP BBQ as you will be connecting the ARTP-SB2 side
burner BEFORE the regulator. (Diagram to the right shows
disconnected fitting for illustrative purposes only)
STEP 8:
Using a pipe wrench or other appropriate tool, install the 1/2"
NPT close nipple provided in the kit.
NOTE: All gas fittings MUST be installed with Teflon pipe
sealing compound or Gas Approved (yellow) - Pipe Teflon
Tape. (These items are not supplied on the kit and must sup-
plied by the customer or installation contractor)
Next, install the 1/2" NPT Tee vertically with the middle
opening oriented to the left side of the grill.
Install the additional 3/8" COMP x 1/2" NPT adapter provided
in the middle of the 1/2" NPT Tee.
Connect the 3/8" Ø x 54" long gas line from the ARTP-SB2
Side burner and tighten the compression nut.
Install the 3/8" ODF (LP) or 1/2" ODF (NG) adapter saved
from the previous step, back into the 1/2" NPT Tee and re-
connect the supply gas lines.
Restore pressure to the system by opening the LP Gas Tank
Valve or NG main shut off valve and check all fittings for
leaks with soap and water.
WARNING: DO NOT LIGHT UP THE BBQ OR SIDE
BURNER IF YOU SMELL GAS. CHECK ALL FITTINGS
FOR LEAKS PRIOR TO LIGHTING UP THE BURNERS.
NOTE: CART AND ELECTRICAL
POWER CORD NOT SHOWN TO
SIMPLIFY VIEW
3/8" LP GAS LINE REGULATOR
(PROVIDED IN LP FACTORY UNITS)
1/2" NPT
TEE
3/8" COMP X 1/2" NPT ADAPTER
3/8" LP GAS LINE REGULATOR
(PROVIDED IN LP FACTORY UNITS)
Figure # 7
1/2" NPT ELBOW
GAS REGULATOR
3/8" ODF (LP) or
1/2" NPT (NG) ADAPTER
1/2" NG GAS LINE
(BY CUSTOMER)
Figure # 8
GAS REGULATOR
1/2" NPT CLOSE NIPPLE
3/8" Ø GAS LINE TO
SIDE BURNER
3/8" ODF (LP) or 1/2" ODF (NG)
ADAPTER
1/2" NG GAS LINE
(BY CUSTOMER)
6