Asko D5223XXLFI Manual de instruções de instalação - Página 5
Procurar online ou descarregar pdf Manual de instruções de instalação para Máquina de lavar loiça Asko D5223XXLFI. Asko D5223XXLFI 16 páginas. Xxl dishwasher
Também para Asko D5223XXLFI: Manual de Planeamento e Conceção (3 páginas)
Imprimir página
CUSTOM DOOR PANEL DIMENSIONS
FITTING THE D5232XXLFI, D5233XXLFI, D5251XXFI, D5253XXLFI, D5531XXLFI,
D5731XXLFI, D5833XXLFI ASKO-MADe Or cuStOM DOOr pAneL - 4 Inch tOe KIcK.
The D5232XXLFI, D5233XXLFI, D5251XXFI, D5253XXLFI,
D5531XXLFI, D5731XXLFI and D5833XXLFI can be
installed with a fully integrated, buyer supplied custom
door panel or ASKO accessory panel that extends from the
toe kick to the counter top. The unit comes with everything
needed to make installing the door panel easy. The door
is predrilled for the panel's mounting screws.
The custom panel should be a minimum of 3/4" (19mm)
thick.
Items provided with the unit
Two 3/8" screws (B) for temporarily hanging the
panel.
Six 1-3/4" screws (D) for mounting the custom
wooden panel to the dishwasher.
INSTALLING THE CUSTOM PANEL OR
ASKO AcceSSOrY pAneL - 4 Inch tOe
KICK
A custom door panel should be installed before the unit
is mounted to the cabinet.
Refer to the illustration at the right for
instruction references.
1. Fit the handle (A) onto the panel according
to the manufacturer's instructions. (NOTE: A
handle should be used rather than a knob,
because a knob does not provide enough
grip.)
IMPORTANT! The custom panel must not obstruct the
fan exhaust vent; otherwise, moisture from the vent
could eventually damage the cabinet and create drying
problems.
2. The two short screws (B) go into the back of the panel
15-7/16" (392 mm) from the upper edge of the panel and
10-7/8" (266 mm) from the center of the panel. Insert the
short screws into the panel, leaving 1/8" (3 mm) of space
between the screw head and the panel.
3. Hook the panel screws (B) into the keyholes (C) on the
dishwasher door.
4. Slide the panel to the left until it is centered in the
opening and secure the screws.
5. Open the door and use the six screws (D) supplied to
secure the panel to the door.
NOTE:
If the door panel weighs more than 15 pounds, you
may need to order the heavy-duty door springs.
*Max panel width cannot exceed cutout dimensions less
1/8" (2.5mm) reveal on each side.
Custom Panel Dimensions
Width
Height
Weight:
Thickness:
ADJUSTING THE DOOR SPRINGS
Before you push the dishwasher into the cabinet opening,
test the door to make sure it stays in place at any angle. If
it tends to fall down, pull out the machine and adjust the
tension of the door springs on the sides of the machine
by moving them one hole farther back or by twisting the
spring to make it shorter.
Customer Care Center
1-800-898-1879
www.askousa.com
23-1/2" (597mm)*
29-7/8"
(760
Measured from the
mm)
top of the panel to
lower edge of the
kitchen cabinet.
Up to 15 lbs.Up
to 20 lbs. with ac-
cessory spring.
3/4" (19mm)
Shorten
D
D
D
Page 5