ASLINKAMP LB-DA1AW Руководство

Просмотреть онлайн или скачать pdf Руководство для Монитор ASLINKAMP LB-DA1AW. ASLINKAMP LB-DA1AW 14 страниц.

Печатать страницу

AnyWireASLINK System Products Guide

ASLINKAMP

[Analog Output Unit

(Ch-to-Ch Isolated Type with 7-segment Display)]

L□-D□1AW

Note on use ⇒ A separate Address Writer is required to set addresses

■

and other data.

For more information, refer to [Various Settings] on page 8.

[Type]

LA-DA1AW

Master unit

Current

Slave unit

LB-DA1AW

[Notes on Safety]

Precautions that must be observed in order to use this system safely are indicated as

shown below. You must observe these precautions.

A WARNING indicates a potentially hazardous situation which, if not

！

WARNING

handled correctly, could result in death or serious injury.

A CAUTION indicates a potentially hazardous situation which, if not

！

CAUTION

handled correctly, may result in personal injury or property damage.

○ System Safety

！

WARNING

This system is intended for general industrial applications. It

does not have functions for supporting applications requiring

higher levels of safety such as safety-related devices or

accident prevention systems. The product must not be used

for these purposes.

○ Always turn off the power in installing or replacing the system.

○ Prolonged continuous ow of a rated load current or higher or

a transit current due to load short-circuit, etc., in the hybrid

unit including the output unit and the output circuit may result

in smoking or ring. An external safety device such as a fuse

must be installed.

○ System power supply

！

CAUTION

Use a stable, 24V DC power supply. Use of an unstable

power supply may cause problems with the system.

○ Separately route high-voltage and power cables

Although the AnyWireASLINK has a high noise margin, install

the transmission line and I/O cables away from high-voltage

and power cables.

○ Connectors and terminals

- Consider the length and securing method of cables so that

the cables and connectors would not be subjected to any

stress and, even if they are under stress, they would not

become loose.

- Make sure to prevent any metal objects from getting inside

the connectors or the terminal blocks.

- Short-circuits caused by metal objects or mis-wiring are

likely to damage the device.

○ Do not impose any external loads on the units. Doing so may

cause a failure.

○ Do not disconnect or reconnect between the transmission

line and slave units when the transmission line is active. A

malfunction may occur.

○ Use the AnyWireASLINK within the range of the speci cations

and conditions shown below.

[Warranty]

■ Warranty period

The warranty on the delivered Product shall continue to be effective for one (1) year

after the delivery thereof to a location as designated by the original owner.

■ Scope of warranty

Should a defect occur in any part of the Product during the foregoing warranty

period when it is used normally in accordance with the speci cations described in

this Products Guide, the Company shall replace or repair the defect free of charge,

except when it arises as a result of:

[1] Misuse or abuse of the Product by the owner;

[2] Fault caused by other than the delivered Product;

[3] The unauthorized modi cation or repair of the Product by any person other than

the Company's personnel;

[4] Any unusual force of nature, disaster or other cause beyond the Company's control.

The term "warranty," as used herein, refers to the warranty applicable to the

delivered product alone. The Company shall not be liable for consequential or

incidental damages resulting from any malfunction.

■ Repair at cost

After the expiration of the warranty period, the owner shall be responsible for all

costs and expenses incurred for the troubleshooting and repair of the Product. Even

during the warranty term, the Company shall repair any defects arising from causes

other than within the scope of the warranty as speci ed above, at the owner's cost.

Ver.1.1

LA-DV1AW

Master unit

Voltage

Slave unit

LB-DV1AW

-L*D*1AW 1/14-

■ Changes in the product speci cations and the descriptions in the manual

The descriptions in this manual may be subject to change without notice.

[About AnyWireASLINK Ver. 1.1]

New functions have been added to AnyWireASLINK products in May 2019

onward. Also, for the purpose of differentiation of compatible functions,

indication of product lot number (lot No.) has been changed.

Compatible functions vary depending on lot No. Please understand the following

description thoroughly to use each product.

Functions added to Ver. 1.1 are as follows:

Functions available with Ver. 1.1

Word transmission*

Single unit simpli ed replacement*

1 To use these functions, the master unit compatible with each function is required.

For details, refer to this manual together with the manual for the master unit.

2 You can use this function with the word-transmission AnyWireASLINK system connected.

To handle word data, word address settings are required for slave units.

It depends on slave units whether word address setting is enabled or not.

[About Lot No.]

As a result of the addition of functions, indication of lot No. has been changed

from 3 digits (conventional format: year and month only) to 6 digits or 7 digits.

Example:

Lot No. 19ECBNB

Year and month

Year: Numbers

(Lower two digits of the Christian era)

Month: Alphabet (as per the table below)

Alphabet

Month

"19E" means May 2019.

3 Some products have no indication of function version.

[About Pictogram

]

Ver. 1.0

Compatible with

Ver. 1.1

4 The pictogram may not be marked (or stuck) depending on the product.

5 AnyWireASLINK device not compatible with Ver. 1.1 (word transmission and single unit

simpli ed replacement functions)

Some products, not marked with the Ver. 1.1 pictogram, are compatible with the

functions included in Ver. 1.1. Refer to the lot No. and the product guide for ultimate

con rmation.

[About Word Transmission]

The master unit compatible with the word transmission function provides areas for

transmission and receiving of word data (numerical information) such as analog

data and sensing level data.

Using this function enables reduction of occupancy of bit information area by

word data.

To enable word transmission, it is necessary that the system should be con gured

only with slave units compatible with the word transmission function.

A slave unit incompatible with the word transmission function cannot be

connected to the AnyWireASLINK system to conduct word transmission.

For slave units that handle word data, word address settings are required.

Function version

S/W version

H/W version