Aero Mist Professional Misting System 52500 Инструкции по установке - Страница 2

Просмотреть онлайн или скачать pdf Инструкции по установке для Открытый фонтан Aero Mist Professional Misting System 52500. Aero Mist Professional Misting System 52500 2 страницы. 12ft copper professional misting system

Печатать страницу

��

Tape Measure

Screwdriver

��

Power Drill with 1/4" Bit (if using anchors)

Tubing Cutter (if customizing length)

5/8" Open-End Wrench

9/16" Open-End Wrench

��

1. Start by measuring the length of your patio perimeter (or perimeter of the

��

2. Start installation by connecting Flexible Nylon Tube (52516) to outlet

3. Use Brass Elbow (52511) to connect Pre-Fabricated Misting Line

��

TOOLS REQUIRED

INSTALLATION INSTRUCTIONS

area to be misted). Proper installation of your new Aeromist Professional

Misting System requires mounting the Pre-Fabricated Misting Line

(52519) on the bottom outside edge of the fascia, header or beam of

patio perimeter. It is important to mount the line along the bottom edge, to

prevent mist from spraying on structure. This installation will create a curtain

of mist around your patio or misted area and provide maximum cooling.

The Aeromist Extension Kit (52501) extends your system by 6 ft. Add

multiple extension kits to custom ﬁ t a misting system to your patio or misted

area mist up to 150 ft (more with optional pump). See the enclosed ac-

cessories brochure or go to www.aeromist.com for a sample of additional

accessories and upgrades available including high-pressure pumps for in-

creasing your misting system's cooling performance and length.

compression ﬁ tting on the Sediment Filter (52505). Finger tighten brass

ﬁ tting, then insert tubing until it bottoms out in ﬁ tting. Complete seal with

one wrench turn of ﬁ tting. Use Vinyl-Coated Clamps, Screws And

Anchors (52509) to secure nylon tubing and ﬁ lter to the side of the struc-

ture. Use Brass Union (52510) to connect additional tubing.

(52519) to Flexible Nylon Tube (52516), secure Pre-Fabricated

Misting Line (52519) to the bottom outside edge of fascia, header or

beam with Vinyl-Coated Clamps, Screws And Anchors (52509). If

necessary, cut the Pre-Fabricated Misting Line (52519) with a tubing

��

LIST OF ALL ENCLOSED PARTS

QTY PART NO

DESCRIPTION

52505

Sediment Filter

52519

Pre-Fabricated Misting Line (6' section)

52516

Flexible Nylon Tube (6' section)

52502

.014 Misting Nozzle

52511

Brass Elbow

52510

Brass Union

52513

Brass End Plug

52509

Vinyl-Coated Clamp, Screw and Anchor

cutter. Never use a saw to cut copper tubing, this will leave burrs and pre-

vent the compression joints from sliding over the tubing. Space clamps on

Pre-Fabricated Misting Line (52519) 24" apart. Use Brass Union

(52510) to join sections of Pre-Fabricated Misting Line (52519).

Terminate system with Brass End Plug (52513).

4. Connect garden hose to inlet of Sediment Filter (52505) and ﬂ ush sys-

tem for several minutes before inserting nozzles. While system is ﬂ ushing

start inserting the .014 Misting Nozzles (52502) nozzles nearest the

ﬁ lter ﬁ rst. Shut water off to insert last nozzle. Caution: hand-tighten

only. Never use pliers to tighten nozzles.

MAINTENANCE

• When turning the misting system off, it is beneﬁ cial to drain the water out

of the line by disconnecting the garden hose at the ﬁ lter. This will help

eliminate mineral buildup.

• Nozzles require cleaning or replacement periodically. Clean nozzles by

soaking in vinegar or calcium removal product overnight.

• Replace ﬁ lter annually, water conditions may require replacement sooner.

• Winterize your misting system by removing all nozzles. Be sure all water

is drained from misting lines. This will prevent water from freezing and

damaging the mist line. For summer season start-up, follow Step 4 in the

Installation Instructions.

Note: Misting system is intended for outdoor use only.

��