ADEMCO 5806 Инструкции по установке - Страница 4

Просмотреть онлайн или скачать pdf Инструкции по установке для Дымовая сигнализация ADEMCO 5806. ADEMCO 5806 4 страницы. Smoke detector with built-in wireless transmitter
Также для ADEMCO 5806: Инструкции по установке (5 страниц)

Печатать страницу

Testing The Smoke Detector

The following procedure should be performed to determine strong radio path communica-

tion with the QED control, and again after installation is completed. THIS TEST SHOULD

ALSO BE PERFORMED ON A REGULAR BASIS (AT LEAST WEEKLY) BY THE USER.

1. Activate the wireless system's TEST

mode via the keypad.

2. Depress and hold the smoke detector's

TEST button. Within 20 seconds, the

detector's horn will start to sound. The

detector will begin to transmit alarm

signals (about once every 4 seconds)

within 6 seconds of the horn sounding.

3. The wireless system's keypad should

emit at least 3 audible sounds when

the alarm transmission is received, and

will display the transmitting detector's

ID number.

4. When satisfied that the keypad has

received the test signal, release the

TEST button. Within 10 seconds the

Testing the Tamper Function (if used) after Mounting the Detector

With the system in the normal disarmed mode, temporarily detach the smoke detector from

its mounting plate. The system's keypad should display a CHECK message. If it does not ,

check that the magnet has been installed in the correct location next to the detector. Also,

check that the wire tamper jumper in the detector has been cut.

SUMMARY OF DETECTOR FUNCTIONS

POWER/ALARM LED

HORN

Pulses every 40

Silent

seconds

Pulses every 40

Beeps once every 40

seconds

Rapid flashing

On continuously

Specifications

Power Source:

Two 9-volt alkaline batteries. Use Ademco 464,

Eveready 522, Duracell MN1604, or equivalent.

Power/Alarm LED:

Standby = flashing once every 40 seconds.

Alarm

= rapid flashing.

Low Battery Signal: One horn "chirp" every 40 seconds.

Size:

5-5/8" inch (14cm) diameter, 2-1/2" inch (6.4cm) high.

TO THE INSTALLER

Regular maintenance and inspection (at least annually) by the installer and frequent

testing by the user are vital to continuous satisfactory operation of any alarm system.

The installer should assume the responsibility of developing and offering a regular

maintenance program to the user as well as acquainting the user with the proper

operation and limitations of the alarm system and its component parts.

Recommendations must be included for a specific program of frequent testing (at least

weekly) to insure the system's proper operation at all times.

– 6 –

detector's horn will stop. A few seconds

later, the smoke detector's ID number

will be cleared from the keypad display.

5. If the keypad does not respond as

noted, check battery connections and

be sure batteries are fresh. If this is an

initial installation, try moving the

detector to another location that

provides proper reception. Repeat test.

Note: Be sure that the detector's ID

has been "enrolled" by the QED control

during programming (see information

on Programming on pages 1 and 2).

6. Turn off the system's TEST mode via

the keypad (security code + OFF).

STATUS

Normal, functioning properly

Low battery or detector

malfunction

Alarm, detecting smoke

THE LIMITATIONS OF THIS

SMOKE DETECTOR/TRANSMITTER

While this smoke detector/transmitter is a highly reliable device that is part of an

advanced wireless security system, it does not offer guaranteed protection against fire.

While smoke detectors have played a key role in reducing residential fire deaths, they

may not activate or provide early warning for a variety of reasons in as many as 35% of

all fires. Some of the reasons smoke detectors used in alarm systems may not work are

as follows:

•

Smoke detectors will not work without power. Battery operated devices will not work

without batteries, or if the batteries are not put in properly.

•

Smoke detectors may have been improperly installed and positioned. Smoke

detectors may not sense fires that start where smoke cannot reach the detectors, such

as in chimneys, in walls, or roof, or on the other side of closed doors. Smoke detectors

also may not sense a fire on another level of a residence or building. A second floor

detector, for example may not sense a first floor fire or basement fire. In addition,

smoke detectors have sensing limitations. No smoke detector can sense every kind of

fire every time. In general, detectors may not always provide adequate warning about

rapidly spreading fires caused by carelessness and safety hazards like smoking in

bed, violent explosions, escaping gas, improper storage of flammable materials,

children playing with matches, or arson. Depending on the nature of the fire and/or

location of the smoke detectors, the detector, even if it operates as anticipated, may

not provide sufficient warning to allow all occupants to escape in time to prevent injury

or death.

•

Alarm signals sent by the wireless transmitter in this device may be blocked or

reflected by metal before they reach the alarm receiver. Even if the signal path has

been recently checked during a weekly test, blockage can occur if a metal object is

moved into the path.

•

Alarm warning devices such as sirens, bells or horns may not alert people or wake up

sleepers if they are located on the other side of closed or partly open doors. If warning

devices are located on a different level of the residence from the bedrooms, then they

are less likely to waken or alert people inside the bedrooms. Even persons who are

awake may not hear the warning if the alarm is muffled by noise from a stereo, radio,

air conditioner or other appliances, or by passing traffic. Finally, alarm warning

devices, however loud, may not warn hearing-impaired people or waken deep

sleepers.

•

This smoke detector/transmitter, like other electrical devices, is subject to component

failure. Even though this device is designed to last as long as 20 years, the electronic

components in it could fail at any time. We recommend that smoke detectors be

replaced every 10 years as a precautionary measure against component failure.

The most common cause of an alarm system not functioning when a fire occurs is

inadequate maintenance. The alarm system should be tested weekly to make sure all

smoke detectors and their transmitters are working properly. Detectors must be repaired

or replaced when they do not function properly.

Installing an alarm system may make the owner eligible for lower insurance rates, but an

alarm system is not a substitute for insurance. Homeowners, property owners and

renters should continue to act prudently in protecting themselves and continue to insure

their lives and property.

We continue to develop new and improved protection devices. Users of alarm systems

owe it to themselves and their loved ones to learn about these developments.

– 7 –