DBI SALA Flexiguard 8530579 Руководство пользователя - Страница 11
Просмотреть онлайн или скачать pdf Руководство пользователя для Промышленное оборудование DBI SALA Flexiguard 8530579. DBI SALA Flexiguard 8530579 16 страниц. Safrig fall arrest system
Печатать страницуCaUtIon:
Personnel shall not be attached to the Flexiguard SafRig Fall Arrest System while it is being positioned.
2. cONFIGure uPrIGHt AssemBLy rOtAtION: The Upright Assembly can be locked at 11° rotation increments with
the Rotation Lock Pin Mechanism or allowed to rotate through a range defined by two Rotation Limiters.
A. NO rOtAtION: (See Figure 11-A) Rotate the Boom to the desired position and then insert the Rotation Lock Pin
through the inside Pin Hole and aligned hole in the Rotation Plate to prevent the Jib Boom from rotating.
B. rOtAtION rANGe: (See Figure 11-B) Insert the Rotation Lock Pin through the outside Pin Hole and then install
Rotation Limiters on each side of the Lock Pin: Remove the Rotation Limiters from their storage positions on the
Jib Boom. Insert the Rotation Limiter mounting pegs through the desired holes in the Rotation Plate to define the
rotation range.
CaUtIon:
The Flexiguard SafRig Fall Arrest System may be used without the Rotation Lock Pin inserted, allowing 360° rotation;
but can cause increased swing fall in multiple directions in the event of a fall.
3.8
rescue AND retrIeVAL
4.0
Use
WarnInG:
Consult your doctor if there is any reason to doubt your fitness to safely absorb the shock from a fall arrest or suspension.
Age and fitness seriously affect a worker's ability to withstand falls. Pregnant women or minors must not use DBI-SALA equipment unless
in an emergency situation.
WarnInG:
Never exceed the Capacity maximums specified in Table 1. Exceeding the stated capacity could collapse or tip the system,
resulting in serious injury or death.
4.1
BeFOre eAcH use: Verify that your work area and Personal Fall Arrest System (PFAS) meet all criteria defined in
Section 2 and a formal Rescue Plan is in place. Inspect the Flexiguard SafRig Fall Arrest System per the 'User' inspection
points defined on the "Inspection and Maintenance Log" (Table 2). If inspection reveals an unsafe or defective condition,
do not use the SafRig Fall Arrest System. Remove the system from service and contact Capital Safety regarding
replacement or repair.
saFe WorK area:
in Figure 6 designates unsafe working distances where the difference between the Vertical Fall Distance (F) and the Vertical Distance
from the Anchorage Connection Point (V) is more than 4 ft. (1.2 m). NEVER work at a Horizontal Distance (H) and Vertical Distance (V)
that results in a calculated Vertical Fall Distance (F) that exceeds the values in the black area in the table in Figure 6.
4.2
FALL Arrest cONNectIONs: Figure 12 illustrates application of the Flexiguard SafRig Fall Arrest System and its Fall
Arrest Connections. The system must always be used with a Full Body Harness and Fall Arrest subsystem.
WarnInG:
When transferring between SRLs, always maintain 100% tie-off to ensure fall arrest protection in the event of a fall.
Important:
No more than one person, meeting the Capacity requirements specified in Table 1, shall be attached to the Flexiguard
SafRig Fall Arrest System.
WarnInG:
Inappropriate or incompatible connections between components of the Personal Fall Arrest System (PFAS) may result in
serious injury or death. See Section 2 for details regarding connector compatibility and safe connections.
4.3
OPtIONAL rescue AND retrIeVAL KIt
add rescue and retrieval capability to the SafRig system.
5.0
InspeCtIon
5.1
INsPectION FrequeNcy: The Flexiguard System must be inspected at the intervals defined in Section 1. Inspection
procedures are described in the "Inspection and Maintenance Log" (Table 2). Inspect all other components of the Fall
Protection System per the frequencies and procedures defined in the manufacturer's instructions.
5.2
DeFects: If inspection reveals an unsafe or defective condition, remove the Jib Boom Assembly from service
immediately and contact Capital Safety regarding replacement or repair. Do not attempt to repair the Jib Boom Assembly.
Important:
Only Capital Safety or parties authorized in writing by Capital Safety may make repairs to this equipment.
5.3
PrODuct LIFe: The functional life of the System is determined by work conditions and maintenance. As long as the
product passes inspection criteria, it may remain in service.
6.0
maIntenanCe, serVICInG, storaGe
6.1
cLeANING: Periodically clean The System with a soft brush, warm water, and a mild soap solution. Ensure parts are
thoroughly rinsed with clean water.
Important:
Although highly resistant to chemicals and environmental conditions, avoid contaminating the Flexiguard Anchorage
System with acids, bitumen, cement, paint, cleaning fluids, etc. If the equipment contacts acids or other caustic chemicals, remove from
service and wash with water and a mild soap solution. Inspect per Table 2 before returning to service.
6.2
serVIce: Only Capital Safety or parties authorized in writing by Capital Safety may make repairs to this equipment.
If the anchor has been subject to fall force or inspection reveals an unsafe or defective conditions, remove the anchor
from service and contact Capital Safety regarding replacement or repair.
6.3
stOrAGe: When not in use, store the System and associated fall protection equipment in a cool, dry, clean environment
out of direct sunlight. Avoid areas where chemical vapors may exist. Thoroughly inspect components after extended
storage.
: Figure 13 illustrates installation of a winch system to add rescue and retrieval capability.
Figure 6 illustrates the Safe Work Area for the Flexiguard SafRig Fall Arrest System. The black area in the table
: Section 3.4 and Figure 13 describe installation of a winch and cable to
11