Brother ImageCenter ADS2500W Руководство по быстрой настройке - Страница 22
Просмотреть онлайн или скачать pdf Руководство по быстрой настройке для Сканер Brother ImageCenter ADS2500W. Brother ImageCenter ADS2500W 37 страниц. High-speed desktop document scanner
Также для Brother ImageCenter ADS2500W: Руководство по безопасности продукции (20 страниц), Руководство (16 страниц), Руководство (20 страниц), Брошюра (2 страниц)
Печатать страницу
For Wireless Network Users
Manual setup from the
10
control panel using the
Setup Wizard (Macintosh,
mobile devices and
Windows
You must have the wireless settings you
wrote down for your network in step 9-b on
page 18 before you proceed.
You cannot configure an enterprise wireless network
using the Setup Wizard from the control panel. If you
choose the SSID for configuring an enterprise
wireless network after searching the available SSIDs,
the message dialog about Enterprise Authentication
Method will appear.
To configure an enterprise wireless network, use
installer DVD-ROM and follow the instructions.
a
Press
.
Swipe up or down, or press a or b to display
Network, and then press Network.
Swipe up or down, or press a or b to display
WLAN, and then press WLAN.
Swipe up or down, or press a or b to display
Setup Wizard, and then press
Setup Wizard.
When Enable WLAN? is displayed, press Yes
to accept.
This will start the wireless setup wizard.
To cancel, press No.
b
The machine will search for available SSIDs. It
will take several seconds to display a list of
available SSIDs.
If a list of SSIDs is displayed, swipe up or down,
or press a or b to choose the SSID you wrote
down in step 9-b on page 18. Select the SSID
you want to connect with, then press OK.
If the wireless access point/router of the
selected SSID supports WPS and the machine
asks to use WPS, go to c.
If the machine asks you to enter a Network
Key, go to d.
Otherwise, go to e.
Note
• If a list of SSIDs is not displayed, make sure
your access point is on. Move your machine
closer to the access point and try starting
from a again.
• If your access point is set to not broadcast the
SSID, you will have to manually add the SSID
name. For details, see the Network User's
Guide.
22
®
)
c
Press Yes to connect your machine using
WPS. (If you choose No (Manual) to
continue manual configuration, go to d to enter
a Network Key.)
When the LCD shows Start WPS, press the
WPS button on your wireless access
point/router, and then press Next to proceed.
Go to e.
d
Enter the Network Key you wrote down in
step 9-b on page 18 using the Touchscreen.
Press
to cycle between lower case and
upper case. Press
letters, numbers and special characters. (The
characters available may differ depending on
your country.) To move the cursor to the left or
right, press d or c.
(For more information, see Entering Text for
Wireless Settings on page 35.)
Press OK when you have entered all the
characters, then press Yes to apply your
settings.
e
Your machine will now try to connect to your
wireless network. It may take a few minutes.
f
A connection result message appears until the
OK button is pressed on the LCD.
If your wireless device is connected
successfully, the LCD shows Connected.
If the connection failed, the LCD shows an
error code. Make a note of the error code, see
Troubleshooting on page 25, and correct the
error.
Wireless setup is now complete. A four
level indicator at the top of your
machine's LCD will show the wireless
signal strength of your access
point/router.
To install MFL-Pro Suite, continue to
step 11.
®
For Windows
users:
Now go to
Page 28
For Macintosh users:
Now go to
Page 31
to cycle between