Indesit FDEF31111 Информация о сервисе - Страница 13

Просмотреть онлайн или скачать pdf Информация о сервисе для Посудомоечная машина Indesit FDEF31111. Indesit FDEF31111 20 страниц.

Печатать страницу

Indesit

Company

FAULT CODES - Detailed

FAULT

LED'S

CODE

1-2

1-3

PRESSURE SWITCH

2-3

1-2-3

1-4

2-4

1-2-4

3-4

1-3-4

1-2-3-4

Service Manual UK

NAME

POSSIBLE CAUSE

ANTI-FLOODING

Bowl oat microswitch electrical

OVERFLOW

circuit OPEN! (must be closed)

WATER FILL

Fill valve admits water even when

SOLENOID VALVE

deactivated.

FAILURE

DRAIN TIMEOUT

Maximum drain time elapsed.

THERMISTOR (NTC) circuit not

THERMISTOR (NTC)

compliant (break in continuity or

not compliant

short-circuit)

Pressure switch has not indicated

completion of fill, even though

turbine has filled appliance with

non compliant

water correctly.

Maximum interval of time for com-

WATER FILL

pletion of ll has been exceeded.

TIMEOUT

Turbine has given no signal indicat-

WATER TURBINE

ing entry of water, even though ll

damaged

has effectively been completed.

Maximum interval of time for es-

TEMPERATURE

tablishing temperature has been

TIMEOUT (1 hour)

exceeded (1 hour).

Software recogni-

Software recognition error Proces-

tion error. Main

sor not programmed.

board not pro-

grammed

HEATING ELE-

HEATING ELEMENT CIRCUIT not

MENT CIRCUIT not

compliant (circuit open).

compliant

No communication/power between

Wash Pump Failure

BLDC/BLAC motor and main board,

or motor seized.

COMMUNICATION

No communication/connection

error between main

between main board and user

board and display

interface.

Main board NOT

Main board NOT WORKING

WORKING

Reading between Wash pump and

VIRTUAL SENSOR

Drain pump not consistent.

- Water leak;

- Float switch or wiring defective;

- New main board: Eeprom was programmed

off-site; to reset the alarm, switch off and switch

on again using the ON/OFF button.

- Fill solenoid valve failure;

- Main board ll solenoid valve triac short-circuiting;

- Make certain drain hose is not on the oor.

- Drain pump blocked by foreign matter;

- Drain pump faulty/disconnected;

- Drain hose blocked;

- Drain trap blocked;

- Air bubble in hose;

- Check drain pump wiring and connectors at

component end and main board end;

- Check integrity of drain pump impeller;

- Replace drain pump.

- NTC sensor cables disconnected or damaged;

-Cablesorconnectorsdisconnectedorshort-circuiting;

- NTC sensor wet, short-circuit;

- NTC sensor damaged, open circuit.

- Pressure switch faulty;

- Pressure switch tube damaged;

- Water in air trap;

- Air trap damaged.

- Tap closed or partially closed;

- Filler hose pinched;

- Filler hose lter clogged/bent;

- Water pressure low or ow meter doesn't work;

- Water solenoid valve faulty or disconnected.

- Turbine faulty or disconnected;

- Connector terminals not making contact;

- Turbine wiring faulty;

- Turbine faulty, disconnected or wet;

- WATER has been introduced manually;

- Filler hose lter obstructed;

- Pressure switch faulty.

- NTC sensor bracket detached from bowl;

- Fault in electrical circuit of heating element;

- Heating element ITR incorrectly calibrated/faulty;

- Excessive suds;

- Heating element false contact

- NTC sensor incorrectly calibrated

- Lime scale on heating element.Water hardness

setting not compliant. User not putting in salt

- NTC sensor separated from socket (replaces

rst check)

- Heating element defective.

- Main board not programmed;

- Incorrect setting le.

- Heating element cables disconnected;

- Main board relay defective

- Heating element defective;

- Main board relay defective.

- Motor connectors disconnected;

- Wiring not compliant;

- Foreign matter between motor blades;

- Motor defective/seized.

- Fault in Main board/user interface wiring;

- Disconnect from electrical power supply.Wait 2

minutes. Reconnect appliance to power supply

and test again;

- User interface defective.

- Replace main board.

- Replace wash pump.

13 of 20

CHECKS

English