Aqua Science CLEAR MAX Руководство пользователя - Страница 5

Просмотреть онлайн или скачать pdf Руководство пользователя для Диспенсер для воды Aqua Science CLEAR MAX. Aqua Science CLEAR MAX 10 страниц. 4 and 5 stage models

Печатать страницу

A q u a S c i e n c e A Z . c o m

Solutions For Life

Illustration of

Drilling Sink

(instruction on previous page)

4. Installing the Drain Clamp

NOTE: If you have a single-basin

sink with a disposal unit, call

Technical Support for options.

NOTE: Before installing the drain

clamp, check the drain pipes under

the sink for corrosion. Corroded

pipes should be replaced before

continuing with installation.

• Attach the drain clamp to a vertical section of the drain pipe, about 6

inches above the trap. Make sure the opening on the drain clamp is facing

towards the drinking water faucet.

• Using the fitting hole of the drain clamp as a guide, drill a 1/4-inch hole

through one side of the drainpipe.

C A L L F O R S E R V I C E 4 8 0 - 8 9 4 - 0 7 7 0

• Remove the drain clamp from the

drain-pipe and enlarge the hole

with a 3/8-inch drill bit. Use a file

to remove rough edges from the

drilled hole.

• Make sure the black rubber gas-

ket is adhered to the inside of the

drain clamp and place the drain

clamp assembly over the drilled

hole. Look through the hole and

posi-tion the clamp so that the

center of the clamp hole is slightly

higher (about 1/16-inch) than the

center of the drilled hole.

• Tighten the clamp securely.

• Screw the plastic compression nut onto the drain clamp until hand-tight.

Connecting the Faucet to the Drain

CAUTION

This is a gravity drain line. Any loops, kinks or sharp bends must be

eliminated before proceeding. Failure to create a straight line to the drain

may result in reject water leaking through the air gap in the faucet onto the

countertop and below the faucet.

1. Align the larger reject (3/8-inch) black tubing from the faucet with the

compression nut on the drain clamp. Create as straight and smooth a path

as possible with the tubing. Do not kink tube. Cut the tubing squarely below

the nut and remove the internal and external burrs.

2. Loosen the compression nut two complete turns. Insert the black tubing

into the nut until it stops. Tighten with fingers, then tighten 1 to 2 turns with

a wrench.

6. Installation of Mounting Screws

1. If system is being installed under the kitchen

sink, locate it on back or right wall. Make sure

to allow ample space for installation. To change

the filter cartridges, a minimum of 1-1⁄2 inches

of clearance is required under-neath the filter

housings. A minimum of 2 inches of clear-ance

from the left side of the unit is also required or

5 inches from the left bracket mounting screw

hole.

2. Install mounting screws at least 15 inches from

cabinet floor and 7-inches apart.

3. Leave a 5/16-inch space between the head

of the screw and the wall to slip bracket onto

screws.

NOTE: Each section of tubing on the RO Assembly has a cap that must be removed

before inserting tubing. Please remove all cap during installation.

7. Connecting the Faucet and the Drain to the System

1. Locate the reject or drain 1/4" black tubing from the drinking water faucet.

This tube is the smaller of the two. Place a mark on the tubing 5/8-inch

from the end. Moisten the end of the tubing with water and insert tubing

into the quick-connect fitting on the flow restrictor found on the of system

behind the membrane. If tubing is not firmly connected, leaking will occur.

It is important for the tubing to be inserted all the way until the mark is

flush with the outer edge of the quick-connect insert.

NOTE: Tubing may be quickly and easily removed from the fitting if

necessary by pressing the collar around the fitting then pulling the tubing

with your other hand.

2. The blue tube from the bottom of the faucet threaded metal tube is

inserted into the outlet of the post filter. Push the free end of the tubing

into the quick connect fitting.

CAUTION