Dell E2210Hf Руководство пользователя - Страница 29
Просмотреть онлайн или скачать pdf Руководство пользователя для Монитор Dell E2210Hf. Dell E2210Hf 30 страниц. Flat panel monitor
Печатать страницу
A. Ensure that the screen is clean (no dust particles on the surface of the screen).
B. Unplug the video cable from the back of the computer or monitor. The monitor then goes into the self-test mode.
C. Press and hold the 1st and 4th buttons on the front panel, simultaneously for 2 seconds. A gray screen appears.
D. Carefully inspect the screen for abnormalities.
E. Press the 4th button on the front panel again. The color of the screen changes to red.
F. Inspect the display for any abnormalities.
G. Repeat steps E and F to inspect the display in green, blue, and white colored screens.
The test is complete when the white screen appears. To exit, press the 4th button again.
If you do not detect any screen abnormalities upon using the built-in diagnostic tool, the monitor is functioning properly. Check the video card and computer.
Common Problems
The following table contains general information about common monitor problems you might encounter and the possible solutions.
Common Symptoms
No Video/Power LED off
No Video/Power LED on
Poor Focus
Shaky/Jittery Video
Missing Pixels
Stuck-on Pixels
Brightness Problems
Geometric Distortion
Horizontal/Vertical Lines
Synchronization Problems
Safety Related Issues
Intermittent Problems
Missing Color
Wrong Color
Great user manuals database on
What You Experience
No picture
Ensure that the video cable connecting the monitor and the computer is properly
l
connected and secure.
Verify that the power outlet is functioning properly using any other electrical equipment.
l
Ensure that the power button is depressed fully.
l
No picture or no brightness
Increase brightness & contrast controls via OSD.
l
Perform monitor self-test feature check.
l
Check for bent or broken pins in the video cable connector.
l
Run the built-in diagnostics.
l
Picture is fuzzy, blurry, or
Perform Auto Adjust via OSD.
l
ghosting
Adjust the Phase and Pixel Clock controls via OSD.
l
Eliminate video extension cables.
l
Reset the monitor to Factory Settings.
l
Change the video resolution to the correct aspect ration (16:9).
l
Wavy picture or fine movement
Perform Auto Adjust via OSD.
l
Adjust the Phase and Pixel Clock controls via OSD.
l
Reset the monitor to Factory Settings.
l
Check environmental factors.
l
Relocate the monitor and test in another room.
l
LCD screen has spots
Cycle power on-off.
l
Pixel that is permanently off is a natural defect that can occur in LCD technology.
l
Run the built-in diagnostics.
l
LCD screen has bright spots
Cycle power on-off.
l
Pixel that is permanently off is a natural defect that can occur in LCD technology.
l
Run the built-in diagnostics.
l
Picture too dim or too bright
Reset the monitor to Factory Settings.
l
Auto Adjust via OSD.
l
Adjust brightness & contrast controls via OSD.
l
Screen not centered correctly
Reset the monitor to Factory Settings.
l
Auto Adjust via OSD.
l
Adjust brightness & contrast controls via OSD.
l
Screen has one or more lines
Reset the monitor to Factory Settings.
l
Perform Auto Adjust via OSD.
l
Adjust Phase and Pixel Clock controls via OSD.
l
Perform monitor self-test feature check and determine if these lines are also in self-test
l
mode.
Check for bent or broken pins in the video cable connector.
l
Run the built-in diagnostics.
l
Screen is scrambled or appears
Reset the monitor to Factory Settings.
l
torn
Perform Auto Adjust via OSD.
l
Adjust Phase and Pixel Clock controls via OSD.
l
Perform monitor self-test feature check to determine if the scrambled screen appears in
l
self-test mode.
Check for bent or broken pins in the video cable connector.
l
Restart the computer in the safe mode.
l
Visible signs of smoke or
Do not perform any troubleshooting steps.
l
sparks
Contact Dell immediately.
l
Monitor malfunctions on & off
Ensure that the video cable connecting the monitor to the computer is connected
l
properly and is secure.
Reset the monitor to Factory Settings.
l
Perform monitor self-test feature check to determine if the intermittent problem occurs in
l
self-test mode.
Picture missing color
Perform monitor self-test feature check.
l
Ensure that the video cable connecting the monitor to the computer is connected
l
properly and is secure.
Check for bent or broken pins in the video cable connector.
l
Picture color not good
Change the Color Setting Mode in the Color Settings OSD to Graphics or Video
l
depending on the application.
Try different Color Preset Settings in Color Settings OSD. Adjust R/G/B value in Color
l
UserManuals.info
Possible Solutions