Ayra 9000-0019-2042 Руководство пользователя - Страница 14
Просмотреть онлайн или скачать pdf Руководство пользователя для DJ оборудование Ayra 9000-0019-2042. Ayra 9000-0019-2042 20 страниц. Dmx cob led light kit with power outputs
Печатать страницу
Installation and maintenance
Installing the system in a standing position (right side up)
The ComPar KIT 3 is equipped with a 35mm stand adapter, which makes it
possible to position the system on a standard speaker or light stand. A double
screw knob is provided to tighten the system, so it is unable to pivot. This also
prevents unwanted rattle noise caused by speaker vibrations, and possible
instability as tube diameters of stands may vary slightly.
Installing the fixture in a standing position (inverted)
It is possible to use the LED projectors as a floor spotlight system, for example
when you want to use them for uplighting purposes. For this feature, use the
screw knobs at the top of the system and mount a floor stand on each side
(included). Use the menu option to invert the display status for easy reading
of values. After this, flip the system and position the bar as you wish.
Installing the fixture in a suspended position
When installing the system in a suspended position (for example, on a truss
construction), detach the screw knobs and install proper G-clamps or half
couplers (not included).
NOTE: When installing the system in a suspended position, the following list
of safety precautions must be met:
- Use at least two rigging points (clamps), for optimal stability and safety.
- Use at least one (recommended amount: 2) safety cable(s), capable of holding 5x the weight of the system.
Safety cables must be installed in such a way that it is impossible for the system to fall down when one of the
two rigging points breaks.
- It is prohibited to install the system by using only safety cables or chains!
The warranty is void if any of the above safety precautions are not met. Ayra cannot be held responsible if
any damage or injury occurs due to improper use of the system.
Lens mechanism
The Compar Kit 3 spotlights are equipped with a standard lens. As the standard dispersion of a COB LED is
very wide, users may want to change the dispersion angle for different purposes. The Compar Kit 3 has
standard lenses installed in front of the spotlights, mounted with two knobs. By loosening the knobs, the
lenses can be removed and stored in the transport bag. The standard dispersion angle of the Compar Kit 3 is
about 30 degrees. When the lens is removed, the dispersion is approximately 120 degrees - ideal for wall
washing, hall ambient lighting and much more! The overall intensity of the Compar Kit 3 may appear to be
brighter if the lens is installed. This is caused by the dispersion of the light intensity over a smaller surface.
Transport
If you use this fixture in a mobile setup, make sure to provide sufficient protection during transport. Always
use the provided transport bags to protect the system and included lighting stand.
Replacing the internal fuses
First check whether a failing power supply may be the cause of malfunction. When you suspect that one of
the internal fuses is broken, the fuse can be replaced after removing the fuse cover, located on the rear of
the fixture, near the power inputs, outputs and control menu.
WARNING: Before checking the fuse, always disconnect the fixture from your wall outlet or any other power
supply to prevent electric shocks.
Always replace the broken fuse with a fuse of the same type and rating. After the fuse has been replaced,
always close the fuse cover. Reconnect the fixture to your power supply and check whether the problem is
solved. If not, contact your local dealer for help.
Spare parts
This unit has no user-serviceable parts inside. When any damage to internal components occurs, contact
Any information and illustrations shown in this user manual are subject to change without further notice.
User manual version: 1.0
Creation date + author initials: 22-04-2015 RV Revision date + author initials: -