Epson L200 Руководство по эксплуатации - Страница 30

Просмотреть онлайн или скачать pdf Руководство по эксплуатации для Принтер "все в одном Epson L200. Epson L200 47 страниц. Color inkjet printer
Также для Epson L200: Технические характеристики (4 страниц), Руководство пользователя (4 страниц), Инструкции (4 страниц), Начните здесь (2 страниц), Руководство пользователя (2 страниц), Уведомления и гарантия (12 страниц)

Печатать страницу

L200/L201/L100/L101

Upper Housing Assy / Ink Supply Holder Assy (L100/L101)

Left side

Step 1

Ink Supply Holder Assy

Hook

C.B.P-TITE SCREW 3x6 (5.0 ~ 6.0 kgf·cm)

Step 4

Left side

Ink Supply Holder Assy

5.0 mm

30.0 mm

Voluntary Label

Do not lift the Upper Housing Assy too fast, since the Panel FFC is connected to the back of the Upper Housing Assy.

Be careful not to damage the hooks (x2) on the bottom left because these cannot be seen when removing.

Follow the procedure below when removing the Upper Housing Assy.

1. Remove the screws (x2) that secure the Ink Supply Holder Assy.

2. Remove the screws (x2) that secure the Upper Housing Assy.

3. Release the hooks (x8) that secure the Upper Housing Assy.

4. Lift the Upper Housing Assy while leaving the Ink Supply Holder Assy.

5. Disconnect the Panel FFC from the connector on the main board, and remove the Upper Housing Assy.

When replacing the Upper Housing Assy, peel off the Voluntary Label from the old housing and attach it to the new housing as specified in the

figure above.

When installing the Ink Supply Holder Assy, align the hooks (x4) of it with the holes of the Upper Housing Assy and then tighten the screws in

the order indicated in the figure above.

Disassembly/Assembly

Bottom side

Step 3

Upper Housing Assy

Rear side

Step 2

Upper Housing Assy

C.B.P-TITE SCREW 3x10 (5.0 ± 0.5 kgf·cm)

Step 5

Upper Housing Assy

Panel FFC

Details of Disassembling/Reassembling by Parts/Unit

Refilling Ink Label (L100/L101)

4.0 mm

Hook

Upper Housing Assy

23.2 mm

Attach the Refilling Ink Label on the position shown in the figure

above.

Ink Tube Guide 1st

C.B.P-TITE SCREW 2.5x5

(5.0 ~ 6.0 kgf·cm)

Follow the procedure below when removing the Ink Supply Holder Assy / Ink Tube Guide 1st.

1. Remove the Upper Housing Assy.

2. Peel off the acetate tape (x2) that secure the Ink Tube Guide 1st.

3. Remove the screw (x1) that secures the Ink Tube Guide 1st.

4. Release the hooks (x2) that secure the Ink Tube Guide 1st, and remove it from the frame.

5. After confirming the Valve is closed, disconnect the Ink Tubes from the Joint.

6. Pull out the Ink Tubes from the holes of the Ink Supply Holder Assy / Ink Tube Guide 1st, and remove the Ink Supply Holder Assy / Ink Tube

Guide 1st.

10.0 mm

4.0 mm

Refilling Ink Label

Be careful when removing the Printer Cover, because the hooks

(x2) are fragile and easily get damaged or softened.

Ink Tube Guide 1st / Ink Supply Holder Assy (L100/L101)

Joint

Ink Tube

Ink Tube Guide 1st

Hook

(p 30)

(p 27)

(p 10)

Revision A

Printer Cover (L100/L101)

Hook

Printer Cover

Holes

Ink Tube

Ink Tube Guide 1st

Ink Supply Holder Assy

Confidential