Pioneer CLD-901 Руководство по эксплуатации - Страница 34
Просмотреть онлайн или скачать pdf Руководство по эксплуатации для CD-плеер Pioneer CLD-901. Pioneer CLD-901 40 страниц. Compact disc/laservision player
Также для Pioneer CLD-901: Руководство по эксплуатации (40 страниц)
TROUBLESHOOTING
Before concluding that the player is out of order, please refer to this troubleshooting guide to make sure that there
is not a simple remedy for the problem.
The vast majority of performance problems have their source in set up
Find the
errors, bad connections to other equipment, or malfunctions of other equipment (TV, stereo system}.
trouble symptom
on the chart below, and try the suggested remedies.
SYMPTOM
CAUSE
e@ Power cord is not properly plugged into AC
wall socket.
@ Power switch is not turned on.
1
Disc table is not expelled
when EJECT button is pressed.
REMEDY
@ Plug in power cord.
@ Turn on power switch.
2
Automatic start not
functioning.
e@ Other equipment connected to |/O port on rear.
3
Disc table is expelled after
PLAY indicator blinks for
approx. 10 seconds.
@ Disc is warped or dirty.
@ Moisture has condensed on parts in the player.
4
Player stops part way through
|
playback, and disc table opens.
® Automatic start function cannot be used when
controlling through I/O port.
e Refer to instructions under Remedy",
item 11,
and correct or clean disc.
@ Remove disc and let player stand for 1 to 2 hours
until it is dry.
5
TV no longer receives other
e@ Antenna cable has not been connected.
channels after it has been
connected to the player.
e LVP indicator is lit, and player is in LVP mode.
——CxX
SYSTEM
(4
s—_ =
ax —
e@ Connect VHF antenna cable to antenna terminal
on the player.
@Press the TV/LVP key on the remote contro!
unit to turn the indicator off, or turn off the
player's power switch.
cx
SYSTEM
ft
ee
6
Slanting stripes appear on the
TV screen when TV/LVP key
is pressed to receive TV
broadcasts.
@ Electric field for TV broadcasting is weak.
(This does not indicate any trouble.)
@ Remote control unit batteries are weak.
@ There is an obstacle between the player and
the remote control unit.
e Remote control unit is not in a good location for
transmission.
@ Other equipment is connected to {/O port on rear
panel, or a plug is inserted in CONTROL
IN
terminal.
Remote contro! does not
work.
®@ Some TV sets have remote control functions that
operate improperly in response to the remote
control unit of the player.
Operation of the remote
control! unit causes the TV to
operate improperly.
WHEN
A LASERVISION
DISC
IS BEING
PLAYED
SYMPTOM
9
Disc rotates but there is no
picture.
e The TV set is not turned on.
Wrong connections from player to TV.
@ TV set is not turned to channel 3 or 4:
e Player VHF CHANNEL SELECTOR
is at the
wrong setting.
@ Piayer is in the PAUSE mode.
e@ LVP indicator is not lit.
34
<VRB1001>
'
@ Turn off the power switch of the player.
We recommend that you turn off the power
switch of the player, whenever you intend to
watch TV for a long time.
e Replace batteries.
e@ Remove the obstacle or shift the remote control
position.
e Operate the remote control unit in front of the
player.
'
@ Commands from remote control not accepted
when I/O port or CONTROL
IN terminal are in
use.
@ Move the TV and the player further apart, or
cover the remote sensor of the TV during disc
playback.
REMEDY
e Turn on TV,
e@ Make correct connections.
e@ Set TV to the channel (3 or 4) that is not used
for TV broadcasting in your area.
@ Set selector to same channel as the TV's empty
channel.
e Press the PLAY key.
@ Press the TV/LVP key on the remote control
unit so that the LVP indicator turns on.
oe
EP
SEER
PASS
CEE