Ariston LTB 6M019 Руководство по эксплуатации - Страница 5

Просмотреть онлайн или скачать pdf Руководство по эксплуатации для Посудомоечная машина Ariston LTB 6M019. Ariston LTB 6M019 16 страниц.

Печатать страницу

Installation

If the appliance must be moved at any time, keep it in an

upright position; if absolutely necessary, it may be tilted onto

its back.

Connecting the water supply

Adaptation of the water supply for installation should only

be performed by a qualified technician.

The water inlet and outlet hoses may be positioned towards

the right or the left in order to achieve the best possible

installation.

Make sure the dishwasher does not bend or squash the hoses.

Connecting the water inlet hose

• To a 3/4" gas cold or hot water connection point (max.

60°C).

• Run the water until it is perfectly clear.

• Screw the inlet hose tightly into position and turn off the

tap.

If the inlet hose is not long enough, contact a specialist

store or an authorised technician

The water pressure must be within the values indicated

in the Technical Data table - otherwise the dishwasher may

be function properly.

Make sure the hose is not bent or compressed.

Connecting the water outlet hose

Connect the outlet hose to a drain duct with a minimum

diameter of 2 cm. (A)

The outlet hose connection must be at a height ranging from

40 to 80 cm from the floor or surface where the dishwasher

rests.

Before connecting the water outlet hose to the sink drain,

remove the plastic plug (B).

Anti-flooding protection

To ensure floods do not occur, the dishwasher:

- is provided with a special system which blocks the water

supply in the event of anomalies or leaks from inside the

appliance.

Some models are also equipped with the supplementary

safety device New Acqua Stop*, which guarantees anti-

flooding protection even in the event of a supply hose rupture.

WARNING: HAZARDOUS VOLTAGE!

(see Assistance)

MAX 80 cm

MIN 40 cm

Under no circumstances should the water inlet hose be cut

as it contains live electrical parts.

Electrical connection

Before inserting the plug into the electrical socket, make

sure that:

• The socket is earthed and complies with current

regulations;

• the socket can withstand the maximum load of the

appliance as shown on the data plate located on the inside

of the door

(see chapter Description of the appliance);

• The power supply voltage falls within the values indicated

on the data plate on the inside of the door.

• The socket is compatible with the plug of the appliance. If

this is not the case, ask an authorised technician to replace

see Assistance

the plug (

). Do not use extension cables or

multiple sockets.

Once the appliance has been installed, the power supply

cable and the electrical socket should be easily accessible.

The cable should not be bent or compressed.

If the power supply cable is damaged, have it replaced

by the manufacturer or its authorised Technical Assistance

Service in order to prevent all potential hazards.

Assistance)

The Company shall not be held responsible for any

incidents, if these regulations are not observed.

Positioning and levelling

1. Position the dishwasher on a level sturdy floor. If the floor is

uneven, the front feet of the appliance may be adjusted until

it reaches a horizontal position. If the appliance is levelled

correctly, it will be more stable and much less likely to move

or cause vibrations and noise while it is operating.

2. Before recessing the dishwasher, stick the adhesive

transparent strip

under the wooden shelf in order to protect

it from any condensation which may form.

3. Place the dishwasher so that its sides or back panel are in

contact with the adjacent cabinets or the wall. This appliance

can also be recessed under a single worktop

Assembly instruction sheet)

. To adjust the height of the rear foot, turn the red hexagonal

bushing on the lower central part at the front of the dishwasher

using a hexagonal spanner with an opening of 8 mm. Turn the

spanner in a clockwise direction to increase the height and

in an anticlockwise direction to decrease it.

instruction sheet attached to the documentation)

Only available in selected models.

(See

(see the

(see Building-in