Zanussi ZDT6453 Книга инструкций - Страница 6
Просмотреть онлайн или скачать pdf Книга инструкций для Посудомоечная машина Zanussi ZDT6453. Zanussi ZDT6453 19 страниц.
Печатать страницу
Setting electronically
The dishwasher is factory set at level 5. If it's necessary to set
a new level, proceed as follows.
1. With the dishwasher switched off, press the On/Off push
button, all indicator lights of the programme push buttons
will illuminate (setting mode).
2. Press simultaneously function push buttons 2 and 3, the
indicator lights of the function push buttons 1, 2 and 3 start
flashing.
3. Press the function push button 1, the indicator lights of
function push buttons 2 and 3 turn off while the indicator
light of the push button 1 goes on flashing, at the same time
the "end of programme" indicator light illuminates, along
with a sequence of audible signals.
The current level is indicated by the number of flashes and
audible signals.
Example: 5 flashes + 5 audible signals = level 5
4. To change the level, press push button 1. Each time the
push button is pressed the level changes.
Examples:
if the current level is 5, by pressing push button 1 once,
level 6 is selected.
if the current level is 10, by pressing push button 1 once,
level 1 is selected.
5. To memorise the operation, switch off the dishwasher by
pressing the On/Off push button or wait about 60 seconds
after which the dishwasher will automatically return to
setting mode.
Filling with salt
Special salt can be added in one of two ways:
If you are using dishwasher detergent that already contains
salt, the detergent including the salt is placed in the
detergent compartment.
- In this case the water softener must manually be set to 1
and electronically to 1 to ensure that the special salt is
taken from the detergent container only.
If you are using dishwasher detergent and salt separately,
the special salt is to be put into the salt container.
- In this case the water softener must manually be set to 1
or 2 and electronically between 1 and 10 (depending on
the water hardness in your area) to ensure that the
special salt is taken from the salt container only.
Only use salt specifically designed for use in
dishwashers.
All other types of salt not specifically designed for use in
a dishwasher, especially table salt, will damage the water
softener.
Only fill with salt just before starting one of the washing
programmes (not the Rinse and Hold programme).
This will prevent any grains of salt or salty water, which
may have been spilt, remaining on the bottom of the
machine for any period of time, which may cause
corrosion.
To fill:
1. Open the door, remove the lower basket and unscrew the
cap of the salt container by turning it anticlockwise.
2. Pour 1 litre of water inside the container (this is necessary
only before filling with salt for the first time).
3. Using the funnel provided,
pour in the salt until the
container is full.
4. Replace the cap making
sure that there is no trace
of salt on the screw thread
or on the gasket.
5. Screw on the cap tightly
turning it clockwise until it
stops with a click.
The salt container will require topping up periodically. You are
reminded of this by the salt indicator light on the control panel
which comes on when the salt has finished.
Do not worry if water over flows from the unit when filling with
salt, this is quite normal.
The salt indicator light on the control panel can remain
illuminated for 2-6 hours after the salt has been
replenished, assuming the dishwasher remains switched
on. If you are using salts that take longer to dissolve then
this can take longer. The function of the machine is not
affected.
23
SR14