ARO 8213-1B Руководство по эксплуатации

Просмотреть онлайн или скачать pdf Руководство по эксплуатации для Шлифовальный станок ARO 8213-1B. ARO 8213-1B 7 страниц. 0 series

Печатать страницу

OPERATOR'S MANUAL

SECTION

M10

MANUAL

INCLUDING: OPERATION, INSTALLATION & MAINTENANCE

Released:

2/86

Revised:

1-20-95

"0" SERIES DIE GRINDER (SHORT GRINDER)

Form:

2884-2

Tool

Products

Models:

7015-11-(),

8212-1B-(

) and 8213-1B.

WARNING

READ THIS MANUAL

CAREFULLY

BEFORE

INSTALLING,

OPERATING

OR SERVICING

THIS EQUIPMENT.

FAILURE

TO OBSERVE

THE FOLLOWING

WARNINGS

COULD RESULT IN INJURY.

To aid the operator's

understanding

of proper and safe use of

grinders, the publications,

"Use, Care and Protection of Abrasive

Use only medium and high strength mounted wheels.

Wheels", A.N.S.I. 87.1, and "Safety Code for Portable Air Tools",

Do not use excessive

work pressure.

A.N.S.I. 8186.1, can be purchased

from:

Allow only people who have received training in "proper grind-

er operation" to operate grinder.

American National Standards Institute, Inc.

1430 Broadway

New York, New York 10018

Do not remove any labels. Replace any damaged label.

Use only accessories

recommended

by ARO.

Operate this tool at 90 p.s.i.g. (6.2 bar) maximum air pressure

at the air inlet of the tool.

Disconnect

air supply from tool before removing/installing

mounted wheel, mounted stone or performing other mainte-

nance procedures.

Keep hands, clothing and long hair away from rotating end of

tool.

Anticipate and be alert for sudden changes in motion during

start up and operation of any power tool.

Never exceed rated r.p.m. of tool.

Wear suitable eye and hearing protection while operating tool.

Tool shaft can continue to rotate briefly after throttle is re-

leased.

Do not lubricate tools with flammable or volatile

liquids such as

kerosene, diesel or jet fuel.

Use tool only for purposes for which it was intended.

Never use mounted stone or carbide burr with speed rating

lower than r.p.m. rating of tool.

Use only mounted wheels of the A, B and W shapes.

Repeated prolonged operator exposure to vibrations which may

be generated

in the use of certain hand-held

tools may produce

Raynaud's

phenomenon,

commonly

referred to as Whitefinger

disease.

The phenomenon

produces

numbness

and burning

sensations in the hand and may cause circulation and nerve dam-

age as well as tissue necrosis.

Repetitive

users of hand-held

tools who experience

vibrations

should closely monitor duration

of use and their physical condition.

The use of other than genuine ARO replacement

parts may

result in safety hazards, decreased

tool performance

and in-

creased maintenance

and may invalidate all warranties.

ARO is not responsible

for customer modification

of tools for

applications

on which ARO was not consulted.

Tool maintenance

and repair should be performed by autho-

rized, trained, competent

personnel.

Consult your nearest

ARO authorized

servicenter.

It is the responsibility

of the employer to place the information

in this manual into the hands of the operator.

For parts and service information, contact your local ARO distributor, or the Customer Service Dept. of the Ingersoll-Rand

Distribution

Center, White House, TN at PH: (615) 672-0321,

FAX: (615) 672-0601.

ARO Tool Products

Ingersoll-Rand

Company

1725 U.S. No. 1 North

P.O. Box 8000

Southern Pines, NC 28388-8000

01995

THE ARO CORPORATION

. PRINTED

IN USA.

Part of worldwide Ingersoll-Rand