3M 6000 Инструкции пользователя - Страница 8

Просмотреть онлайн или скачать pdf Инструкции пользователя для Респираторный продукт 3M 6000. 3M 6000 15 страниц. Half facepiece respirator
Также для 3M 6000: Руководство пользователя (4 страниц), Инструкции пользователя (16 страниц), Технический паспорт (5 страниц), Инструктивный лист (2 страниц), Инструктивный лист (8 страниц), Инструкции пользователя (2 страниц)

Печатать страницу

In Brazil, the 3M™ Filter 5935BR used with the 3M™ Adaptor 603 is assembled following the same procedures as the 5N11 and 5P71.

3M™ Supplied Air Systems

To meet the U.S. National Institute for Occupational Safety and Health (NIOSH) requirement for minimum (4 CFM/115 lpm) and maximum (15

CFM/424 lpm) air flow, the air control valves approved for use with the 3M™ Full Facepiece Respirators 6000 Series must be operated within the

correct supply pressure ranges and hose lengths. Failure to do so may result in sickness or death.

In Brazil, the Brazilian Association of Technical Standards (ABNT) NBR 14372 requires a minimum of 120 lpm and maximum of 280 lpm air flow for

breathing air for half and full facepiece respirators.

Your employer must provide breathing air that meets at least the requirements of the specification for Grade D breathing air, as described in the

Compressed Gas Association Commodity Specification G-7.1-1997 in the United States. In Canada, breathing air systems must be supplied with air,

which meets at least the requirements of CSA Standard Z180.1. Failure to do so may result in sickness or death.

In Brazil, breathing air systems must be supplied with air which meets ANSI Z86.1-1989/CGA G-7.1, Grade D breathing air.

3M™ Dual Airline Respirator Assembly

User must follow Dual Airline Supplied Air Respirator User Instructions provided with the 3M™ Dual Airline Supplied Air Respirators.

Assembly of 3M™ Combination Dual Airline Respirator with Cartridges and/or Filters

The SA-1600 (front-mounted) and SA-2600 (back-mounted) versions of the 3M™ Dual Airline Breathing Tubes allow use of selected, NIOSH-

approved 3M™ Cartridges 6000 Series and Filters 2000 Series. For the listing of approved cartridges and filters, reference the NIOSH Approval Label

included with 3M dual airline adapter kits.

To assemble 3M™ Dual Airline Combination Breathing Tubes with 3M™ Cartridges/Filters, the facepiece, inhalation valves must be removed.

IMPORTANT: If the facepiece is to be used in air-purifying mode (without using the SA-1600 or SA-2600 breathing tubes), the inhalation valves must

be replaced in the facepiece before use.

Using the 3M™ Combination Dual Airline Breathing Tubes without Cartridges and/or Filters

To use the 3M™ Combination Dual Airline Breathing Tubes (SA-1600 and SA-2600) without cartridges or filters, attach a 3M™ Bayonet Cap 6880

to each outer bayonet mount on the dual airline breathing tube. When used as a Type C, continuous flow supplied air full facepiece respirator, the

Assigned Protection Factor is 1000 times the PEL or other occupational exposure limit.

The 3M™ Dual Airline is NIOSH approved only with the 3M™ Nose Cup 6894 in place. Failure to do so may result in sickness or death.

FITTING INSTRUCTIONS

Must be followed each time respirator is worn.

NOTE: Do not use with beards or other facial hair or other conditions that prevent a good seal between the face and the faceseal of the respirator.

Standard eyeglasses cannot be worn with full facepiece respirators. If corrective eyeglasses are required a 3M™ Spectacle Kit must be used inside

the respirator. To help maintain a good seal between the face and the faceseal all hair, hoods, or other equipment must be kept out of respirator

faceseal area at all times.

Donning Respirator

1. Fully loosen all four head straps. With one hand pull hair back out of facepiece sealing area. Place chin in the respirator chin cup. While holding the

facepiece in place, pull the head harness to back of head (Fig. 9).

2. Pull the ends of the four straps to adjust tightness, starting with the neck straps first, then the forehead straps. Do not over tighten the straps

(Fig. 10).

3. Perform a positive and/or negative pressure user seal check each time the respirator is donned.

Fig. 6

Requester: Farrel Allen

Creator:

deZinnia

File Name: 12703-4_6000Series.ai

Structure #: NA

Supersedes: NA

Date:

02/03/12

Scale:

1 Inch

W WARNING

Fig. 7

Requester: Farrel Allen

Creator:

deZinnia

File Name: 12703-5_6000Series.ai

Structure #: NA

Supersedes: NA

Date:

01/19/12

Scale:

1 Inch

(English)

Requester: Farrel Allen

Creator:

deZinnia

File Name: 12703-6_6000Series.ai

Structure #: NA

Fig. 8

Supersedes: NA

Date:

01/19/12

Scale:

1 Inch