AMD DIrect Pro Series Kurulum ve Kullanım Talimatları Kılavuzu - Sayfa 10
Brülör AMD DIrect Pro Series için çevrimiçi göz atın veya pdf Kurulum ve Kullanım Talimatları Kılavuzu indirin. AMD DIrect Pro Series 20 sayfaları. Round drop in pan fire pits with thermocouple piloted safety ignition (tpsi) & pro brass snowflake burner
Ayrıca AMD DIrect Pro Series için: Kurulum ve Kullanım Talimatları Kılavuzu (20 sayfalar), Kurulum ve Kullanım Talimatları Kılavuzu (20 sayfalar), Kurulum ve Kullanım Talimatları Kılavuzu (20 sayfalar)
Sayfayı YazdırINJECTOR HOOD/RAIN SHIELD INSTALLATION
Install the hood/rain shields over top of each injector of the
pro brass burner by sliding it into position. Use the bead in
the lower section of the hood, and align it with the groove
in the injector, until it snaps into place. See Fig. 8. Rotate
the hood to ensure it is protecting the injector opening from
the elements (i.e. rain, dirt or media). See Fig. 9 for proper
alignment. Note: If there is no detent in the injector, ensure
the hood is ½" from the base of the injector to the bottom
edge of the hood.
Bead around
the hood
Groove around
the injector
HOOD
INJECTOR
Fig. 8 Installing injector hoods.
Hoods
Injector/Jets
Fig. 9 Correct placement of injector hoods.
CAUTION: It is imperative the "open side" of all hoods
covering the injectors/jets are installed facing downward.
Because the hoods can be removed or turned, the
orientation is extremely important to protect the injector or
jets from dust, dirt or rain. See detail in Fig. 8.
WARNING: Failure to orient the hoods in the
proper position on the burner tube will void
the manufacturer warranty.
Sq. Drop In Pan Fire Pits with Snowflake Burner and (TPSI) Ignition
FINAL PREPARATION
HOOD
1/2"
INSTALLATION OF MEDIA INTO BURNER PAN
Install lava rock into the burner pan. Ensure the lava rock is
a minimum of 1-inch diameter for proper operation.
Note: Do not pour Lava Rock directly from bag. It should
be placed naturally and NOT packed in tight. Loose fitting
is important to ensure robust flames. Placing the lava rock
in the pan by hand, ensures no excessive dust from bag
lays in the bottom of pan and potentially plugs the burner
port holes or the pan weep holes. DO NOT BLOCK
INJECTORS WITH MEDIA.
IF USING AMD DIRECT, INC GL GLASS OR GLR
REFLECTIVE GLASS, ENSURE THE MEDIA DOES NOT
BLOCK THE INJECTOR HOLES.
IMPORTANT: DO NOT PLACE ROCK OVER TOP OR
UNDER THE PILOT SCREEN COVER. The screen must
be free of any debris to ensure proper lighting of burner
and good flame sense (See Fig. 10).
Cover the burner completely with media but do not make
the depth greater than 1-inch over-top of the burner
port holes.
Do NOT cover the top of mesh pilot hood with any rock or
glass. It must be free an any debris to operate properly.
Lava Rock
Screen Cover
Fig. 10 Media placement around pilot hood.
Acceptable media to be placed over top of the burner:
Lava Rock
Min.1"- 2" size
FG-LAVA-10 (10 LB)
FG-LAVA-40 (1 CUBIC FOOT)
GL Glass
Min. ½" - ¾" size
Various colors are available
See Product catalog for details
Sold in 10LB jugs or 6 jugs to a case
GRL Reflective Glass
Min. ½" - ¾" size
Various colors are available
See Product catalog for details
Sold in 10LB jugs or 6 jugs to a case
Lava Rock
Pilot
Screen
Cover
Lava Rock
REV. A
Page 10