Air King AK5500 Kurulum, Çalıştırma ve Bakım Talimatı - Sayfa 6

Nemlendirin Air King AK5500 için çevrimiçi göz atın veya pdf Kurulum, Çalıştırma ve Bakım Talimatı indirin. Air King AK5500 14 sayfaları. Flow-through furnace humidifier
Ayrıca Air King AK5500 için: Broşür (4 sayfalar), Garanti, Bakım, Sorun Giderme Kılavuzu (14 sayfalar), Kurulum, Garanti, Bakım, Sorun Giderme Kılavuzu (14 sayfalar)

Sayfayı Yazdır

1. Humidifier Operation

Furnace Humidifier

CAUTION: When cutting or drilling into ducting take care not to

damage any air-conditioning coils or other furnace apparatus.

CAUTION: Wear safety glasses and work gloves when installing

this unit. Sharp metal edges can cause severe injury.

1. Use adhesive tape to affix the bypass template onto the duct

in the selected location.

2. Drill the 3 marked

" holes.

3. Using a

" drill bit (not supplied) drill a hole inside the circular

area marked collar cut out.

4. Using the

" hole drilled earlier as a starting point cut out the

Collar Cut Out area marked on the template using tin snips

(not supplied).

5. Mount the bypass collar and

damper (Fig. 20) using the three

supplied screws. The air damper

should be installed in the open

position. The top screw secures the

damper.

•INSTALLATION TIP If replacing an existing humidifier

which has been installed on your furnace you may be

able to use the existing cut-outs, however replace the

components, bypass collar and damper, and bypass

ducting. The majority of furnace humidifiers use 6"

ducting for bypass.

STEP #4: WATER SUPPLY AND DRAINAGE CONNECTION

WATER CONNECTION TO THE HUMIDIFIER

IMPORTANT: Connect the tubing to the humidifier FIRST before

connecting to the saddle valve.

1. SAND THE END (Fig. 21) of the

plastic

water

supply

FAILURE TO DO SO MAY RESULT

LEAKS.

Use

sandpaper (not provided) approx

" from the end in a rotating

motion. This assures a non-

slipping, trouble free connection.

2. Slide the nylon compression nut and the black rubber ferrule

onto the sanded plastic tubing and then fit the brass insert into

the end of the plastic tubing. (Fig. 22)

Figure 22

NYLON COMPRESSION NUT

BRASS INSERT

BLACK RUBBER

FERRULE

3. Push the plastic tubing firmly into the humidifier's

float valve threaded water inlet. Carefully begin

tightening the nut by hand. Use an adjustable wrench to finish

tightening. (Fig. 23)

TOP SCREW

FOR DAMPER

MOUNTING

Figure 20

tube.

medium

Figure 21

SANDED TUBE

NOTE: The optimum tightness of the nylon compression nut will

leave a gap of approximately

compression nut and the nylon hex nut.

INSTALLING THE SADDLE VALVE TO THE WATER PIPE

The water supply for the humidifier is provided from an existing

cold water pipe by using a self-piercing saddle valve. In order for

you to use the supplied plastic tubing, select the nearest cold

water pipe suitable for saddle valve installation.

1. Turn the main water supply off.

2. Rotate the saddle valve handle so that the piercing pin does

not protrude beyond the top clamp.

3. With the rubber gasket in the fixed position, clamp the saddle

DAMPER

OPEN

valve on the selected location

of the cold water pipe and

mount the bolts and nuts to

the saddle clamps.

4. To pierce the copper pipe,

simply turn valve handle clock-

wise until you feel that it is

firmly seated. (Fig. 24)

NOTE: Do not open the valve

now. Proceed with the mounting

of the plastic tubing to the saddle

valve first.

CONNECTING THE PLASTIC TUBING TO THE SADDLE VALVE

1. Cut the plastic tubing with a sharp knife to the proper length

to fit between the humidifier and the saddle valve.

2. SAND THE END (Fig. 21) of the plastic water supply tube.

FAILURE TO DO SO MAY RESULT IN LEAKS. Use medium

sandpaper (not provided) approx 1

rotating motion. This assures a non-slipping, trouble free

connection.

3. Slide the brass

compression nut and

nylon ferrule onto the

sanded plastic tube

and fit the brass insert

in the end of the

tubing. (Fig. 25)

4. Push the tubing firmly into the saddle valve threaded water

outlet, carefully begin tightening the compression nut by hand

(be careful not to cross the threads). Use and adjustable

wrench to finish tightening the brass compression nut. Do not

Figure 23

over-tighten.

OVERFLOW DRAIN CONNECTION (OPTIONAL)

NOTE: WE STRONGLY RECOMMEND YOU INSTALL A DRAIN

TUBE TO PROTECT YOUR PROPERTY IN CASE OF WATER

LEAKAGE. IF YOU ARE PLANNING ON INSTALLING A DRAIN

TUBE ONTO THE UNIT YOU WILL HAVE TO PURCHASE THE

REQUIRED LENGTH OF TUBING AND A HOSE CLAMP

SEPARATELY. AS WELL YOU SHOULD HAVE DRILLED OUT

THE DRAIN FITTING BEFORE INSTALLING THE WATER PAN

ONTO THE FURNACE. ONLY DRILL OUT THE WATER PAN IF

YOU PLAN TO INSTALL A DRAIN TUBE.

" between the nylon

ROTATE CLOCKWISE

TO PIERCE PIPE

SELF

PIERCING

VALVE

RUBBER

PIERCING PIN

GASKET

TOP

CLAMP

BOTTOM

CLAMP

Figure 24

" from the end in a

BRASS

SANDED TUBE

INSERT

BRASS

NYLON

NUT

FERRULE

Figure 25