Bosch FAP-OC 500Series Kullanım ve Bakım Kılavuzu / Kurulum Talimatları - Sayfa 28

Fırın Bosch FAP-OC 500Series için çevrimiçi göz atın veya pdf Kullanım ve Bakım Kılavuzu / Kurulum Talimatları indirin. Bosch FAP-OC 500Series 40 sayfaları. Built-in wall ovens
Ayrıca Bosch FAP-OC 500Series için: Kurulum Talimatları Kılavuzu (21 sayfalar), Kullanım Kılavuzu (40 sayfalar), Kurulum Kılavuzu (6 sayfalar), Ürün Bilgileri (40 sayfalar), Kurulum Kılavuzu (28 sayfalar), Kullanıcı Kılavuzu (48 sayfalar), Kullanıcı Kılavuzu (48 sayfalar), Kurulum Kılavuzu (28 sayfalar), Kullanım ve Bakım Kılavuzu (44 sayfalar), Kurulum Kılavuzu (32 sayfalar), Hızlı Referans Kılavuzu (4 sayfalar), Kullanım ve Bakım Kılavuzu (27 sayfalar), Kurulum Kılavuzu (24 sayfalar), Kurulum Kılavuzu (32 sayfalar), Kullanım ve Bakım Kılavuzu (24 sayfalar), Kurulum Kılavuzu (28 sayfalar), Servis Kılavuzu (41 sayfalar), Kullanım ve Bakım Kılavuzu (21 sayfalar), Kurulum Kılavuzu (32 sayfalar), Servis Kılavuzu (36 sayfalar), Kurulum Kılavuzu (32 sayfalar), Hızlı Başlangıç ve Güvenlik Kılavuzu (13 sayfalar)

Sayfayı Yazdır
Bosch FAP-OC 500Series Kullanım ve Bakım Kılavuzu / Kurulum Talimatları

Default Program and Option settings

At the factory, temperature and spin speed options, and
cycle duration ("Finish in" time) are pre-set for all cycles.
After selection of the cycle, these values are displayed in
the display field.
You can change the default settings as follows.

Changing the temperature range

Before and during the cycle, you can change the default
temperature range depending on the cycle progress.
Press the appropriate button until the desired setting is
displayed.
The maximum temperature range that can be set
depends on the cycle selected.

Changing the spin speed range

Before and during the cycle, you can change the spin
speed range depending on the cycle progress.
Touch the appropriate button until the desired setting is
displayed.

Additional Program Option settings

Extra Rinse

+1, +2
This feature is helpful for locations with very soft water or
to generally improve rinsing results. It allows up to 2
additional rinse cycles to be added to selected programs
and will increase program time.
Prewash
PW
For heavily soiled washing. Pour 1/3 of normal detergent
amount into pre-wash chamber I and remaining 2/3 into
main wash chamber II.

SpeedPerfect

G
For washing in a shorter time with a washing result
comparable to that of the standard program.
Note: Do not exceed the maximum load. ~ Program
selection table; Page 26
28
No Spin: This option eliminates the final spin and the
load remains saturated with the final rinse water. The
pump is activated to remove all residual water.
~ Program selection table; Page 26

Finish in

The program end (Finished in) time can be set in one
hour increments to a maximum of 24 h (hours). After
selecting the desired washing program (at the dial) but
before touching the Start button, touch the Finish in
button until the desired time is displayed, e.g. 8 h, then
touch the Start button to start the washer.
NOTICE: The cycle duration is included in the set Finish
in time.
Here is an example of a 2hr:30min cycle time and an 8 h
Finish in time.
8 h is displayed (until the Energy-Saving mode activates)
and counts down (approximately 5hr:30min) until the
washing cycle begins (at 2hr:30min) then the cycle
duration 2:30 is displayed and began. Total time
approximately 8 hours.