advanced scale models P-61 Black Widow Montaj Talimatları Kılavuzu - Sayfa 3

Oyuncak advanced scale models P-61 Black Widow için çevrimiçi göz atın veya pdf Montaj Talimatları Kılavuzu indirin. advanced scale models P-61 Black Widow 17 sayfaları.
Ayrıca advanced scale models P-61 Black Widow için: Montaj Talimatları Kılavuzu (16 sayfalar)

Sayfayı Yazdır
During the covering process, sometimes color may smear slightly from the seams. If you see any smeared colors on the covering
●
material, it can be quickly removed by simply wiping it off with a paper towel and a small amount of Acetone.
Make sure to test-fit the parts before applying glue. This will ensure that the parts fit together properly before gluing them together.
●
When gluing anything that has a smooth surface, it's important to lightly roughen the gluing surfaces with 220 grit sandpaper. This
●
will allow the glue to stick better. Also, never glue directly to the covering material. Always remove the covering material from the
gluing surfaces prior to gluing the parts together.
When cutting away the covering material from the gluing surfaces, be careful to cut only through the covering material. Try not cut
●
down into the balsa structure because that can compromise the integrity of the airframe.
We do not suggest storing your airplane in an extremely hot environment (like the back of your car in direct sunlight) for any length
●
of time. The extreme heat could cause the covering material to wrinkle or sag and possibly damage the fragile components of the
radio control system.
Epoxy can be cleaned up before it dries using rubbing alcohol and C/A can be cleaned up before it dries using C/A Debonder.
●
Make a U-Shaped bend in one end of a long piece of scrap pushrod wire and use it to help pull the servo extension leads through
●
the wing panels.
The control horns are mounted to the control surfaces using wood screws. Even though the wood screws thread into plywood
●
plates, apply a small amount of 5 minute epoxy to each screw before you install it, for extra security.
When you plug servo extensions onto the servo leads, apply masking tape or heat-shrink tubing over the plugs to prevent any
●
chance of them pulling apart during assembly, or worse, during flight.
Apply threadlocking compound to any screws that thread into metal. This will ensure the screws can't vibrate loose during flight.
●
Apply lightweight oil or petroleum jelly to the pivot point of the rudder hinges and the landing gear door hinges (if applicable) to
●
prevent epoxy from gluing the hinges solid.
Before flying the airplane for the first time, make sure to go through and double-check everything. Check that all the hinges are
●
glued solidly, all bolts and screws are tight, etc. Double-check the operation of the landing gear, too, if using the optional retractable
landing gear.
ADVANCED SCALE MODELS P-61 BLACK WIDOW FINAL ASSEMBLY

STEP 1: HINGING THE AILERONS AND FLAPS

TIPS FROM THE PROS

❑ Hinge the ailerons to the wing panels, using the six C/A-style hinges
provided and a generous amount of thin C/A. Make sure that the tip of
each aileron is even with the wing tip and that the hinge gap is as tight
as possible to prevent flutter.
pRo Tip Push two T-Pins through the center of each hinge to help
keep the hinges centered while you hinge the ailerons. Make sure to
remove the T-Pins before you push the ailerons into their final positions.
This will ensure a tight hinge gap.
❑ Hinge the flaps to the wing panels, using the four C/A-style hinges
provided. Use the same techniques that you used to hinge the ailerons.
Notice that the flaps are hinged along the bottom of the wing.
iMpoRTANT The inboard edge of the flaps should be approximately
1/16" (1.6mm) inside the root rib of the wing panels. This will prevent
the flaps from hitting the center wing panel when lowered.
3
CONTINuED