DS Produkte 06625 Talimatlar Kılavuzu - Sayfa 4
Dış Mekan Işığı DS Produkte 06625 için çevrimiçi göz atın veya pdf Talimatlar Kılavuzu indirin. DS Produkte 06625 11 sayfaları.
EN
■
If the product does fall in water, immediately disconnect the
power supply. Do not attempt to pull the product out of the
water when it is connected to the mains supply!
■
Never touch the product, the adapter, the mains cord and the
plug with wet hands when the product is connected to the
mains.
■
Turn the product off and pull the mains plug out of the socket
– when you are not using the product,
– if a fault occurs during operation,
– before a storm,
– before you clean and/or stow the product.
■
Always pull on the plug itself and never on the mains cord!
■
Only use the product in enclosed areas.
■
Do not use the product in rooms containing easily fl ammable
dust or toxic and explosive vapours.
■
Do not operate the product in a very moist environment or in
the vicinity of fl ammable material.
■
Only use the product if it is correctly assembled and the
product, the remote control, the adapter, the cable or plug do
not exhibit any visible damages. Do not use the product if it
malfunctions, has fallen down or in water.
■
For your own safety, check the product for damages each time
before using it. Only use the product if the product, the adapter,
mains cord and the plug do not exhibit any damages!
■
Never leave the product unattended when it is switched on or
plugged in to the mains supply.
■
Do not make any modifi cations to the product. Also do not
replace the mains cord yourself. Only have the product,
adapter, cord and plug repaired by a qualifi ed workshop.
Contact customer service if necessary. Improper repairs could
pose serious risks for the user.
Proper handling of batteries
■
Before inserting the battery, make sure that the contacts in
the battery compartment and on the battery are clean and, if
necessary, clean them.
■
Only use the battery type specifi ed in the technical data (see
section "Technical data").
■
When changing batteries ensure correct polarity (+/–).
■
Remove the battery from the battery compartment if it is empty
or if you are not using the product. This way, you can avoid
damages attributed to leaking.
■
If a battery has leaked, avoid contact between your skin, eyes
and mucous membranes and the battery acid. In the event of
contact with the battery acid, rinse the affected areas instantly
with plenty of clean water and immediately consult a physician.
■
Immediately remove any leaking batteries from the battery
compartment. Clean the contacts before you insert a new
battery.
■
The battery may not be charged or reactivated with other
means, may not be disassembled, disposed of in fi re, im-
mersed in a liquid or short-circuited.
Damage to material, property and the device
■
Always place the product on a dry surface at a suffi cient
distance to fl ammable objects and sources of heat like
stovetops, ovens, heaters. Do not place any open fl ames, e.g.
burning candles, in the direct vicinity of the product.
■
Do no place any containers fi lled with liquids, e.g.vases, on or
directly next to the product.
■
Do not subject the product to extreme temperatures, severe
changes in temperature or direct sunlight.
■
Do not place any heavy objects on the product.
■
Make sure that the connector cable does not get pinched,
kinked or laid over sharp edges and does not come into con-
tact with hot surfaces.
■
The product may not be used if it exhibits visible damages.
Do not use the product if it had a malfunction or liquid has
penetrated the product.
■
Do not expose the product to severe shocks.
■
Do not use corrosive or abrasive cleaning products to clean
the product. They could damage the surface. When needed,
wipe the product off with a soft, dry cloth.
Product contents
•
1 x daylight lamp with built-in control panel
– 1 x base with barrel connector socket and adapter port
– 1 x tube with outside thread
– 1 x tube with recess for locking screw
– Lamp head with movable neck and control panel including
cable with barrel connector
– 1 x locking screw
•
1 x adapter
•
1x remote control including 3 V type CR2032 button cell
(inserted)
Remote control
8
7
6
Start-up
ATTENTION!
■
The plastic foils and bags pose a suffocation hazard! Keep
children and animals away from the packaging material.
•
Unpack the product contents and make sure that they are
complete (see chapter "Product contents") and check for any
damages from transport. If the product, plug or mains cord
exhibits damages, do not use the product (!); instead contact
customer service.
•
Before you use the product, remove all packaging material and
any labels located on the product and which serve to provide
protection during transport or are for advertising purposes.
Assembly
1. Pull the cable on the lamp head through the two extension
tubes. In the process make sure that you pull it through the
tube with the outside thread fi rst and then through the tube with
the recess for the locking screw.
2. Tighten the tube with the outside thread on the lamp head.
3. Tighten the tube with the recess for the locking screw on the
tube with the outside thread.
4. Connect the port in the base to the barrel connector on the
cable.
5. Insert the tubes in the base.
6. Secure the tubes using the locking screw. Make sure the screw
is located in the recess of the base.
Instructions
comprising:
1 AN/AUS switch (ON/OFF)
2 Warm white light
1
3 Tageslicht (daylight)
4 Farbe (colour)
5 Farbwechsel
change), all colours
2
6 Control panel for colour
3
selection (12 mixed col-
ours)
4
7 RGB setting (red, green,
5
blue)
8 Increase/decrease
brightness
(colour
the