DSC PowerSeries PC1616 Kurulum Kılavuzu - Sayfa 2

Kontrol Paneli DSC PowerSeries PC1616 için çevrimiçi göz atın veya pdf Kurulum Kılavuzu indirin. DSC PowerSeries PC1616 17 sayfaları. System enhancement module
Ayrıca DSC PowerSeries PC1616 için: Kurulum Kılavuzu (13 sayfalar), Hızlı Kılavuz (4 sayfalar), Kurulum Kılavuzu (20 sayfalar), Manuel (18 sayfalar)

Sayfayı Yazdır

Begin the installation by mounting the cabinet in a dry protected area with access to unswitched AC power.

Install Hardware in the sequence indicated below. Do NOT apply power until installation is complete.

NOTE: All wiring entry points are designated by arrows. All circuits are classified UL power limited except for the battery leads.

Minimum 1/4" (6.4mm) separation must be maintained at all points between power limited and non-power limited wiring and

connections.

1. Keybus Wiring

The 4-wire KEYBUS (red, black, yellow and green) is the communication connection between the control panel and all modules. The 4 KEY-

BUS terminals of all modules must be connected to the 4 KEYBUS terminals of the main control panel.

The following rules must be followed when wiring the Keybus:

•

Minimum 22 AWG wire, maximum 18 AWG (2-wire twisted pre-

ferred

•

Do NOT use shielded wire

•

Modules can be home run, connected in series or can be T-

tapped provided that the maximum wire distance from the control

panel to any module does not exceed 1,000 feet (305m)

•

No more than 3,000 feet (915m) of wire can be used in total

2. Zone Wiring

Zones can be wired for Normally Open, Normally Closed Contacts

with Single-end-of-line (SEOL) resistors or Double End-of-Line

(DEOL) resistors. Observe the following guidelines

•

For UL Listed Installations use SEOL or DEOL only.

•

Minimum 22 AWG wire, maximum 18 AWG

•

Do NOT use shielded wire

•

Wire run resistance shall not exceed 100

below.

•

Section [001-004] Selects Zone Definition

•

Section [013] Opt [1] Selects Normally Closed or EOL resistors

•

Section [013] Opt [2] Selects Single EOL or Double EOL resis-

tors.

Zone Status

Loop Resistance

- 0Ω (shorted wire/loop)

- 5600Ω (contact closed)

- infinite (broken wire, open)

- 11,200Ω (contact open)

3. Bell Wiring

These terminals supply 700mA of current at 12V

installations and 11.1-12.6 V

SD-15 WULF). To comply with NFPA 72 Temporal Three Pattern

requirements:

Program Section [013] Opt [8] ON.

The Bell output is supervised and power limited. If unused, connect a

1000Ω resistor across Bell+ and Bell- to prevent the panel from dis-

playing a trouble. See [,][2].

Hardware Installation

Ω.

Refer to the chart

Loop Status

Fault

Secure

Tamper

Violated

for commercial

for residential installations (e.g.DSC

150' (46m)

CONTROL

PANEL

500' (152m)

Normally Closed Loops - Do NOT use for UL Installations

Single End-of-Line Resistor Wiring

Double End-of-Line Resistor Wiring

BELL/SIREN

700mA (max.)

OBSERVE

POLARITY

500' (152m)

NOTE: Bell output is current lim-

ited by 2A PTC

NOTE: Steady, Pulsed and Tem-

poral Three Pattern alarms are

supported.