Anywire AnyWireASLINK BS-K5217-M30-1K Ürün Kılavuzu
Aksesuarlar Anywire AnyWireASLINK BS-K5217-M30-1K için çevrimiçi göz atın veya pdf Ürün Kılavuzu indirin. Anywire AnyWireASLINK BS-K5217-M30-1K 9 sayfaları. Aslink sensor
Sayfayı YazdırAnyWireASLINK System Products Guide
ASLINKSENSOR [ASLINK Sensor]
BS-K5217-M□□-1K
[Notes on Safety]
Precautions that must be observed in order to use this system safely are indicated as
shown below. You must observe these precautions.
A WARNING indicates a potentially hazardous situation which, if not
！
WARNING
handled correctly, could result in death or serious injury.
A CAUTION indicates a potentially hazardous situation which, if not
！
CAUTION
handled correctly, may result in personal injury or property damage.
○ System Safety
！
WARNING
This system is intended for general industrial applications. It
does not have functions for supporting applications requiring
higher levels of safety such as safety-related devices or
accident prevention systems. The product must not be used
for these purposes.
○ Always turn off the power in installing or replacing the system.
○ Prolonged continuous ow of a rated load current or higher or
a transit current due to load short-circuit, etc., in the hybrid
unit including the output unit and the output circuit may result
in smoking or ring. An external safety device such as a fuse
must be installed.
○ System power supply
！
CAUTION
Use a stable, 24V DC power supply. Use of an unstable
power supply may cause problems with the system.
○ Separately route high-voltage and power cables
Although the AnyWireASLINK has a high noise margin, install
the transmission line and I/O cables away from high-voltage
and power cables.
○ Connectors and terminals
- Consider the length and securing method of cables so that
the cables and connectors would not be subjected to any
stress and, even if they are under stress, they would not
become loose.
- Make sure to prevent any metal objects from getting inside
the connectors or the terminal blocks.
- Short-circuits caused by metal objects or mis-wiring are
likely to damage the device.
○ Do not impose any external loads on the units. Doing so may
cause a failure.
○ Do not disconnect or reconnect between the transmission
line and slave units when the transmission line is active. A
malfunction may occur.
○ Use the AnyWireASLINK within the range of the speci cations
and conditions shown below.
[Warranty]
■ Warranty period
The warranty on the delivered Product shall continue to be effective for one (1) year
after the delivery thereof to a location as designated by the original owner.
■ Scope of warranty
Should a defect occur in any part of the Product during the foregoing warranty
period when it is used normally in accordance with the speci cations described in
this Products Guide, the Company shall replace or repair the defect free of charge,
except when it arises as a result of:
[1] Misuse or abuse of the Product by the owner;
[2] Fault caused by other than the delivered Product;
[3] The unauthorized modi cation or repair of the Product by any person other than
the Company's personnel;
[4] Any unusual force of nature, disaster or other cause beyond the Company's
control.
The term "warranty," as used herein, refers to the warranty applicable to the
delivered product alone. The Company shall not be liable for consequential or
incidental damages resulting from any malfunction.
■ Repair at cost
After the expiration of the warranty period, the owner shall be responsible for all
costs and expenses incurred for the troubleshooting and repair of the Product.
Even during the warranty term, the Company shall repair any defects arising from
causes other than within the scope of the warranty as speci ed above, at the
owner's cost.
[Type]
AnyWireASLINK proximity sensor: Built-in ampli er,
BS-K5217-M18-1K
BS-K5217-M30-1K
[Function]
Model
Detection method
Features
[Included in the Package]
BS-K5217-M18-1K
BS-K5217-M30-1K
*
Mounting tting should be purchased separately as required.
*
An Address Writer ARW-04 (Ver. 04-1.01 or later) or ARW-03 (Ver. 2.10
or later) is necessary for setting up the product. Order one at the
same time.
ARW-04
[Name of Each Part]
Detection face
-BSK5217M**1K 1/9-
capacitive type
M18, polyarylate (black)
M30, polyarylate (black)
ASLINKSENSOR 2-wire type (non-isolated)
Capacitive type
Sensitivity adjustment (threshold)
Hysteresis
Alarm determination level
Alarm determination time
Normally open/Normally closed
Delay timer
Slave unit voltage drop
Sensing level drop
Teaching error
This product ... 1
Nut
... 2
The version
number is
displayed at
startup.
This label bears
the description
ARW-04
"Ver.*.**".
Front
Back
Transmission cable
(Oil resistant and flexible type)
Full thread
LINK indicator
IN indicator
ALM indicator
Setting port
BS-K5217-M18-1K shown as an example
READER/WRITER
Ver.04-1.01
LotNo.***
MADE IN JAPAN
DP (Red)
DN (Black)