AFG 2.0AT Kullanıcı Kılavuzu - Sayfa 17

Koşu Bandı AFG 2.0AT için çevrimiçi göz atın veya pdf Kullanıcı Kılavuzu indirin. AFG 2.0AT 20 sayfaları.

AFG 2.0AT Kullanıcı Kılavuzu
m
U
PROBLEM: Operating
speed appears inaccurate.
SOLUTION,: Auto-calibrate the treadmill:
• Power on the treadmill and have the safety key in position
on the console, Press and hold the elevation "+" and
speed "-" buttons for approximately 5 seconds to enter
the Engineering Mode. Theconsole will beep and "ENGO"
appears in the display.
• Press the Speed "+'_or
"-" button until "ENG2" appears in
the display.
• Press, "ENTER" to select. Press, "START" to begin, The
treadmifl running belt will begin to move automatically and
the auto-calibration
sequence wifl properly set and store
the speed values,
• Upon successful calibration, the treadmill will beep several
times, The console will automatically exit Engineering Mode
and return to the start-up screen.
'
: ¸5¸¸¸ _!_
calibrating-
stand on the guide
fluCtuatebetween
Iow and high speeds for severa!
minutes until calibration is complete:
TROUBLESHOOTING
- HEART R ATE
Check yourexercise environment f orsources of interference suchas fluorescent l ights,computers, u nderground fencing,home
security
systems
or appfiances containing large
motors.These itemsmaycauseerraticheartratereadouts.
You may
experiencean
erraticreadoutunderthe
following
conditions:
• Grippingtheheartratehandlebars tootight. Try to maintainmoderate pressure whileholdingontotheheartratehandlebars.
• Constant m ovement a nd vibrationdueto
constantly holding
theheartratehandlebars while
exercising.
Ifyou
are receiving
erraticheartratereadouts,try to onlyhold thegripslong enough to monitor yourheartrate.
• When y ou
are breathing heavily
duringa workout.
• When your hands are constricted by
wearing
a ring.
• When y ourhands
are
dryor cold.
Try
to moisten your
palms by rubbing them together
to warm.
• Anyone with heavyarrhythmia.
• Anyone with arteriosclerosis o r peripheral c irculationdisorder.
• Anyone
whose skin on the
measuring palm is especially
thick.
Thefollowing information may be asked of you whenyou call. Pleasehave these items readily available:
* Model Name
* Serial Number
o Date of Purchase (receipt or credit card statement)
In order for Customer TechSupport to serviceyour treadmill they may need to ask detailed questions about the symptoms that are
occurring. Some troubleshooting questions that may be asked are:
* How long has this problem been occurring?
o Doesthis problem occur with every use? With every user?
o If you are hearing a noise, doesit come from the front or the bach? What kind of noise is it (thumping, grinding, squeaking,
chirping etc.)?
o Has the machine been lubricated and maintained per the maintenance schedule?
Answering these and other questions will give the technicians the ability to send proper replacement parts and the service necessary
to get you andyour AFGtreadmill running again!
ii! :
Cleanliness of your treadmill and its operation environment will keep maintenance problems and service calls to a
minimum. Forthis reason, werecommendthat the following preventive maintenance schedule be followed.
AFTER EACHUSE(DAILY)
Cleanand inspect, following these steps:
,, Turnoff the treadmill with the on/off switch, then unplug the power cord at the waft outlet.
o Wipedown the running belt, deck,motor cover,and consolecasing with a damp cloth. Never use solvents, as they
can cause damageto the treadmill.
,, Inspect the power cord. If the powercord is damaged, contact AFG.
o Make sure the powercord is not underneath the treadmill or in any other area whereit can becomepinched or cut.
o Check the tension and alignment of the running belt. Make sure that the treadmill belt will not damage any other
componentson the treadmill by being misaligned.
EVERY WEEK
Cleanunderneath the treadmill, following these steps:
,, Turnoff the treadmill with the on/off switch, then unplug the power cord at the wall outlet.
,, Fold the treadmill into the upright position, making sure that the lock latch is secure.
,, Move the treadmill to a remote location.
,, Wipeor vacuumanydust particlesor otherobjectsthat mayhaveaccumulatedunderneaththe treadmill.
o Return the treadmill to its previous position.
......................
* Turnoff the treadmill with the on/off switch, then unplug the power cordat the wall outleL
o Inspectallassemblybolts of the machineforproper tightness.
Turnoff the treadmill and wait 6Oseconds.
RemOve the motor cover.Wait until ALLdisplay screensturn off.
clean the motor and lower board area to elirninate any lint or dust particles that rnayhave accurnulated! Failure to
do so may result in prernature failure of keyelectrical components;
, Vacuu m and wipe down the belt With adamp cloth, Vacuu m any black/whiteparticlesthatmayaccurnulate
around
the unit. Theseparticles may accurnulate from normal treadmifl use,
EVERY 6 MONTHS OR 150 MILES
It is necessaryto lubricate your treadmill running deck every six months or
150 miles to maintain optimal performance. Oncethe treadmill reaches
150 miles, the console will display the message "LUBE"or "LUBEBELT".
Thetreadmill will not operate while the messageis showing. Hold Stop for
5 secondsto suspend messagefor 5 miles. Yourtreadmill came with a
bottle of lubricant which can be used for two appficafions. If you need
lubricant contact AFG.Only uselubricant provided by
AFG.
0
0
Turnoff the treadmill with the on/off switch, then unplug the power cord
at the waft outlet.
Loosenboth the rear roller bolts. (Forbest results, place two removable
marks on both sides of the frame and note roller position). Oncethe belt
is loosened, take the bottle of lubricant and apply it to the entire top
surface of the running deck. Tightenboth rear roller bolts (matching up
the marks for proper position) to original position. After you have applied
lubricant, plug in the powercord, insert the safety key,start the treadmill
and walk on the belt for two minutes to spread the lubricant.
Lubricate the air shocks with Teflonbasedspray.
RUNNING B ELT
RUNNING B ECK
Oncelubrication is complete, reset the console by pressing and holding 'STOP' and Speed '+' buttons for 5 seconds.
Pleasecontact AFGwith questions about applying lubricant to your treadmill.
i
iii_ i
2.0AT
Rev.l.9.indd
32-33
3/3/08
11:12:41 AM