ADEMCO VISTA 5140XM Kullanıcı Kılavuzu - Sayfa 4
Güvenlik Sistemi ADEMCO VISTA 5140XM için çevrimiçi göz atın veya pdf Kullanıcı Kılavuzu indirin. ADEMCO VISTA 5140XM 15 sayfaları. Commercial fire & burglary alarm system
Sayfayı YazdırFIRE ALARM SYSTEM OPERATION
CONSOLE FIRE FUNCTIONS
1. ALPHA DISPLAY WINDOW: A 2-line,
32-character Liquid Crystal Display
(LCD).
Displays protection point
identification
and
system
status
messages, and user instructions.
2. OFF KEY: Silences alarms and audible
trouble indicators, and clears visual
displays after the problem has been
corrected.
3. BYPASS KEY: Removes individual
protection zones from being monitored
by the system. Displays previously
bypassed protection zones.
4. # KEY: Is used to activate the Fire Drill
Function.
5. KEYS 0-9:
Used to enter your
individual security code(s).
IMPORTANT!: When using the keypad to enter codes and commands,
sequential key depressions must be made within 3 seconds of one another.
If 3 seconds elapses without a key depression, the entry is aborted and
must be repeated from its beginning.
– 6 –
6. CODE KEY:
Allows the entry of
additional security codes that can be
given to other users of the system.
7. READY KEY:
Displays all faulted
protection zones. This key is also used
to display all zone descriptions that
have been programmed for your
system, by holding this key down for at
least 5 seconds.
8. POWER INDICATOR: (GREEN) Lit
when primary power is on. If off,
system is operating on its backup
battery
power.
CALL
YOUR
INSTALLER IMMEDIATELY.
9. INTERNAL SOUNDER:
Source of
audible
internal
warning
and
confirmation sounds, as well as alarms
( s e e
" S u m m a r y
o f
A u d i b l e
Notifications").
FIRE ALARM SYSTEM OPERATION
NORMAL STANDBY OPERATION
Your fire alarm system is on 24 hours a day
for continuous protection. It will provide the
following visual and audible indications
while in the normal standby mode (i.e.: no
alarm, supervisory or trouble conditions are
present):
1. The console sounder and all external
fire sounders will be silenced
IN CASE OF A FIRE
In the event that a fire emergency occurs,
the strategically located smoke and heat
detectors will automatically send signals to
your control panel which will trigger the
indications described below. Should you
become aware of the fire emergency
before your detectors sense the problem,
go to your nearest console and manually
initiate an alarm by pressing the panic key
pair assigned as FIRE EMERGENCY (if
programmed by your installer) and hold
down for at least 2 seconds. When fire
alarm sounds are heard, evacuate all
occupants from the premises immediately.
SILENCING/RESETTING FIRE ALARMS
1. To silence the console and external
sounder fire alarm sounds, enter your
security code and press the OFF [1]
key. The display window will continue
to display the number of the zone(s) in
alarm and will also display "FIRE
ALARM SILENCED" to indicate that a
fire alarm condition may still be
present.
2. The console green POWER indicator
should be lit indicating that AC power is
present
3. The console display window will display
a message such as "XYZ ALARM
COMPANY" (or "DISARMED - READY
TO ARM" if your system provides
burglary
protection)
which
programmed by your installer at
installation time.
1. The console sounder will produce an
interrupted sound and the external fire
sounders
will produce either an
interrupted or a continuous sound
depending on what was selected by
your installer at installation time.
2. The console display window will display
the word "FIRE" and the number and
alpha descriptor of the zone which is in
alarm. The display window will
sequence through other zone numbers
if more than one zone is in alarm.
3. An alarm
signal will be sent to a
central monitoring station (if your
system was installed with this
capability).
2. To reset your smoke detectors and
clear the console alarm display
indications, first locate and correct the
cause of the fire alarm condition (i.e.:
reset pull stations, fan smoke out of
smoke detector chamber, etc.) and
then re-enter your user code + OFF [1].
NOTE: Detectors will not reset and the
alarm display will not clear while the fire
alarm condition remains.
– 7 –
is