ADEMCO 5890PI Kurulum Talimatları - Sayfa 3

Güvenlik Sensörleri ADEMCO 5890PI için çevrimiçi göz atın veya pdf Kurulum Talimatları indirin. ADEMCO 5890PI 4 sayfaları. Passive infrared motion detector/transmitter

Sayfayı Yazdır

Figure 5. PC Board

TEST PROCEDURES

Important: Testing should be conducted with

the protected area cleared of all people. Place

the protective system's control in the Test

mode for the Walk-Test procedure. When the

PIR senses movement, a beep will be heard

To take full advantage of the pet immunity in the 5890PI, the following guidelines

should be followed:

•

Note: This unit will provide immunity to false alarms for an individual animal or a group of

animals whose total weight is equal to or less than 40 pounds when the room temperature is

above 50 F.

Trouble 1: INTERMITTENT ALARM

Probable Causes:

A. Rapid temperature change. Check for electric or gas

heaters, open flames, electric arcs, etc.

Remedy: Locate source and reposition detector.

B. Drafts causing drapes, light fixtures, display material to

move.

Remedy: Eliminate source of motion.

Trouble 2: LED INOPERATIVE DURING WALK-TEST

Probable Causes:

A. LED control jumper set to NORMAL.

Remedy: Reposition jumper to TEST position.

B. LED malfunction. Check for broken/shorted leads.

Remedy: Return unit for service.

from the system's console, verifying that the

PIR's transmitter signal has reached the

control's wireless receiver.

The absolute range of all PIR units is subject

to variation because of different types of

clothing,

temperature. For this reason, ensure that the

most likely intruder routes are well within

the PIR's protective zones and that Walk -

Testing is carried out along these routes.

Walk-Test

1. Remove front cover and set the pulse

count jumper in the detector in the OFF

position initially.

enabled at this time (jumper in the TEST

position).

2. Replace front cover and walk through

protective zones, observing that the

detector's LED lights whenever motion is

detected (the LED serves as a Walk-Test

indicator during this procedure).

3. If pulse count is going to be used in this

installation, set the pulse count jumper to

the ON setting and repeat the Walk-Test

procedure.

Note: If pulse count mode is used during

the Walk-Test, the LED will stay lit for

TABLE 1. INSTALLATION GUIDE FOR MOUNTING HEIGHTS

Lens

Part

Description/

No.

Coverage

5890PI

PET IMMUNE LENS

(Standard

35 ft x 45 ft

as installed)

(10.6m x 13.7m)

TABLE 2. SPECIAL INSTRUCTIONS FOR INSTALLATION WITH PETS

Mount the center of the detector 6-1/2 to 7-1/2 feet high and adjust the vertical angle

according to Table 1.

Set the Pulse Count to ON.

Mount where animals cannot come within six feet of the detector by climbing on furniture,

boxes, or other objects.

Do not aim the detector at stairways, furniture or objects that can be climbed by an animal.

backgrounds

and

ambient

The LED must be

Pulse

PIR

Count

Mounting Height

Req'd for

6.5 ft (2.0m)

installations

with pets

7 ft (2.1m)

7.5 ft (2.3m)

TRO UBLE S HO O TI NG

Trouble 3: DETECTION AREA CHANGES

Probable Causes:

Repositioned furniture or equipment in the protected area.

Remedy: Caution customer about layout changes. Reposition

detector.

Mounting surface is unstable. A few degrees of vertical shift can

change range substantially.

Remedy: Mount on secure surface.

Trouble 4: UNIT DOES NOT APPEAR TO BE OPERATING

Probable Cause:

Unit is not receiving power.

Remedy:

Check for appropriate battery voltage. Install new

batteries if necessary. Be sure to change both batteries.

approximately 1 to 3 seconds after

detecting motion.

4. After the Walk-Test is completed, the

LED jumper should be placed in the

NORMAL position (LED disabled).

MAINTAINING PROPER OPERATION

In order to maintain the detector in proper

working condition, it is important that the

user observes the following:

1. Replace both batteries within 7 days

after a "low battery" message has

appeared in the system's display.

2. Detectors should never be re-aimed or

relocated without the advice or assistance

of the alarm service company.

3. The physical surroundings of the

protected area should not be changed. If

furniture or stock is moved, or air -

conditioning or additional heating is

installed, the PIR may have to be

readjusted.

4. Walk-Tests

should

frequently (at least weekly) to confirm

continued proper coverage.

† See Figure 5 for

Pattern

Setting

location of

(Deg)

adjustment scale on

PC board (refer also

to "Vertical Pattern

Adjustment")

conducted

OPTIMUM PET

IMMUNITY