Brother MFC-580 Hızlı Kurulum Kılavuzu - Sayfa 2

Faks Makinesi Brother MFC-580 için çevrimiçi göz atın veya pdf Hızlı Kurulum Kılavuzu indirin. Brother MFC-580 6 sayfaları. Facsimile equipment
Ayrıca Brother MFC-580 için: Kurulum Kılavuzu (5 sayfalar), Parça Referans Listesi (21 sayfalar)

Sayfayı Yazdır

Install the Ink Cartridges

Check that the power is turned on (by plugging in the power cord).

The LCD shows:

CHECK CARTRIDGE

Open the control panel cover by pulling it toward you (1), then lift the

top cover toward the back (2). After a few seconds, the print head will

move left to its replacement position.

Top Cover

Control Panel

Cover

WARNING

If ink gets in your eyes, rinse them with water immediately and if

irritation occurs, consult a doctor.

We recommend that you install the ink cartridges from left to right in

this order: Black, Cyan, Yellow, Magenta.

Open the Black ink cartridge bag and take out the ink cartridge.

Carefully remove the sealing tape from the bottom of the ink cartridge.

You should peel the tape in the direction away from you.

Important

To prevent spilling ink and staining your hands and clothing, peel the

sealing tape gently and slowly. Do not touch the ink opening on the

cartridge or the removed tape.

Don't touch

this part

Check Colour Block Quality and Alignment

The MFC starts printing the PRINT QUALITY

CHECK SHEET (only during initial ink cartridge

installation).

Check the sheet to see if the quality and

alignment are OK by following steps A and B.

• The bottom of the white shipping cover is wet with ink that will cause stains, so wipe it clean before

you place it down.

• Do not throw away the white shipping cover. You will need it for future transportation.

Push the four coloured ink cartridge covers one at a time so they pop up. Then remove the white

shipping cover by pulling it toward you and then lifting it up and out.

Each colour has its own correct position. Match the colours of the ink cartridge covers, First, gently

insert the Black ink cartridge, and then press the cover down until it clicks.

Repeat Steps D-F to install each colour ink cartridge.

After installing all ink cartridges, close the top cover and control panel cover until they click into place.

Your MFC will enter a "head cleaning" cycle for approximately four minutes.

Peel in the direction

away from you!

Make sure the paper is loaded in the multi-purpose sheet feeder. The LCD shows CLEANING. After the

cleaning cycle is finished, the LCD shows

Opening

Press

STEP A: Colour Block Quality Check

The LCD shows:

IS STEP "A" OK?

1.YES 2.NO

Check the quality of the four colour blocks printed on the sheet.

(BLACK/CYAN/YELLOW/MAGENTA).

If the quality is OK for all colours, press

STEP B.

—OR—

If white horizontal lines appear in some colour blocks below,

press

(NO).

Poor

The LCD asks you if the print quality is OK for each colour.

BLACK OK?

1.YES 2.NO

Press

(NO) for any colour with a problem.

The LCD shows:

START CLEANING?

1.YES 2.NO

Press

(YES), then MFC starts cleaning the colours.

After cleaning is finished, press

MFC starts printing PRINT QUALITY CHECK SHEET again

and goes back to the first step of STEP A.

Page 2

Ink Cartridge Covers

PRESS FAX

Mono Fax Start and go to Step 8 "Check Colour Block Quality and Alignment".

STEP B: Alignment Check

The LCD shows:

IS STEP "B" OK?

1.YES 2.NO

Check the 600DPI and 1200DPI test print to see if No.5 most

closely matches the OK sample ( 0 ).

(YES) to go to

If No.5 is the best match, enter

Do NOT select

If another test print number is a better match for either 600DPI

or 1200DPI, enter

For 600DPI, enter the number of the test print that most closely

matches the 0 sample (1-8).

600DPI ADJUST

SELECT BEST #

For 1200DPI, enter the number of the test print that most

closely matches the 0 sample (1-8).

Mono Fax Start. The

1200DPI ADJUST

SELECT BEST #

White Shipping Cover

START.

(YES)—OR—

(NO) to select it.

}

600 DPI

}

1200 DPI