Indesit IDL 420 Kurulum ve Kullanım Kılavuzu - Sayfa 18

Bulaşık Makinesi Indesit IDL 420 için çevrimiçi göz atın veya pdf Kurulum ve Kullanım Kılavuzu indirin. Indesit IDL 420 25 sayfaları.

Sayfayı Yazdır

Indesit IDL 420 Kurulum ve Kullanım Kılavuzu

Turning on the Appliance

First of all.

Turn on the water tap completely and press ON-OFF

button "A". you will hear a short beep and indicator light

"B" lights up.

Now the appliance is on and awaiting instructions.

Starting and selecting the cycle.

Turn the cycle selector knob "D" clockwise until the

reference notch on the knob corresponds with the number

or symbol for the cycle you wish to set (consult the wash

cycle table on page 17, especially when first using the

appliance).

If the appliance door is shut, press the Start button "R"

and you will hear a beep; the cycle will start up within a

few seconds.

Cycle phase indicator lights

The dishwasher is provided with 4 indicator lights "G" which

come on in sequence as the appliance is performing that

specific phase of the wash cycle.

These phases are:

pre-wash,

wash,

Cancelling or modifying a wash cycle in progress..

Premise: You can cancel the wash cycle in progress, if it

has only just started.

To modify a wash cycle, keep the RESET button "R"

pressed for about 5 seconds: a prolonged beep will sound,

followed by three short beeps. Indicator light "G" will turn

off and at this point, all the settings will have been

cancelled.

To select a new wash cycle, repeat the operations

illustrated in the paragraph entitled "starting and selecting

the cycle".

Warning: the knob must be turned clockwise from

wash cycle 1 to 5, an anti-clockwise from wash cycle 5 to

If you have left out a dish

You can interrupt a wash cycle by pressing the ON-OFF

button, then place the dishes you had left out into the

appliance, which will start up from where it was interrupted

when you turn it back on.

There's been a power failure? Have you opened the

dishwasher door?

The wash cycle stops and then restarts when the electricity

comes back on or when the door is shut.

rinses,

drying

At the end of the wash cycle.

The end of the wash cycle is indicated by two short beeps

and the flashing of the drying phase indicator light.

Warning:

Press button A to turn the appliance off, unplug the

appliance from the electricity socket to cut off the power

supply; the power supply cable should consequently

be easily accessible.

Turn off the water tap.

Wait a few minutes before unloading the dishes: if you

wait a little while, they dry better thanks to the steam.

Empty the lower rack first.

Warning: when you open the dishwasher door after

the wash cycle has just ended or is under way, take care

not to scald yourself with the hot steam.

You decide when it starts.

When you have loaded the dishes, you can choose when

to start your dishwasher before setting the wash cycle

desired.

Press button "H" to delay the start of the wash cycle by

12, 9, 6 or 3 hours. Each time you press it, you will hear a

short beep and the indicator light "G" corresponding to

the selected delay will come on.

Now you can select the desired wash cycle. Press the

start button "R" and after you hear the beep, the count-

down to the delayed start will begin.

If you have set a 12 hour delay, for example, once you

have selected the wash cycle, the 12 hour indicator light

will flash followed by the others in sequence until the set

time delay is up. A quick look at the indicator lights will

keep you informed of the countdown progress at all times.

Dual function of indicator lights "G"

1) flashing to indicate a delayed start: to remind you

that you have set a delayed start;

2) on and not flashing beneath the cycle phase symbol:

meaning the cycle has started and is in the phase

indicated by the symbol.

Have you changed your mind?

If you change your mind, you can set a shorter time delay:

press button "H" to select it. You need not reset the wash

cycle.

If on the other hand you want to cancel the delay set and

you want the cycle to start immediately, press button "H"

repeatedly until the cycle starts and indicator light "G"

corresponding to the cycle start phase comes on.