Axvue KOEHOG E622 Kullanım Kılavuzu

Bebek Monitörü Axvue KOEHOG E622 için çevrimiçi göz atın veya pdf Kullanım Kılavuzu indirin. Axvue KOEHOG E622 2 sayfaları. Video baby monitor with 2.4 '' lcd screen & two cameras

Sayfayı Yazdır

INSTRUCTION MANUAL

KOEHOG E622 Video Baby Monitor

with 2.4 '' LCD Screen & Two Cameras

Please read the following instructions and warnings carefully

Keep this instruction manual for the future.

For technical support see the FAQ page.

For adult use only.

FEATURES & COMPONENTS

Camera:

Monitor:

*LED

Power & Low Battery

Sound Lights

× 2

WARNING

THIS PRODUCT CAN NOT SUBSTITUE PARENT'S SUPERVISION

ON YOUR CHILD.

-Store this product out of the reach of babies (at least 3 feets (0.9 m)

away from the crib). A strap wound around the baby's neck may result in

asphyxiation. Use a safety clip to clamp the power cord and keep it out

of baby's reach. Do not use other extension cords. Only use the power

adapter provided.

-Do not touch the exposed part if the adapter is connected with power.

-Test regularly before initial use or when change the position of camera.

-Avoid placing the product in humid place or contacting with liquid. (such as bathtub, sink, etc.)

-Do not apply heat to the product.(such as stoves, radiators, etc.)

-Using the product in ventilated place. Avoid placing it on sofas, cushions, beds or other places which

may block ventilation.

-The product only can be operated by adult. Do not allow baby to play with it. Tiny accessories are

contained, please be careful when unpack and install it.

Model- E622

Revised at 11/2020

Get to know us at: www.koehog.com

Keep the distance between sensor and

body at least 0.6 inch for accurate

0.6 in

temperature result.

1. Night-Vision LED

2. Lens

3. Power Indicator

4. Microphone

5. Speaker

6. Power/Code

7. Temperature Sensor

8. DC Jack

9. Wall Mounting Hole

1. LED*

2. Volume Up

3. Power/Video

4. Left

5. Menu/OK

6. Right

7. Talk Back/Zoom

8. Volume Down

9. Microphone

10. Speaker

11. Battery Compartment

12. Kickstand

13. DC Jack

Adapter:

× 3

× 1

BATTERY WARNING

-Only use the recommended rechargeable battery. Please contact us if you need to change it.

For the contact list, please refer to the last page of the instruction.

-Please clean the battery compartment before using it.

-Avoid short circuits the power supply terminal.

-Remove the battery when you are not using it or when running out of power.

-Keep the battery away from children.

-Dispose of the empty battery properly.

SETUP & USE

Please charge the battery for at least 8 hours before

using the product.

Step 1: Test reception ﬁrst, put camera in a suitable place

that will provide you the best view of your baby in the crib

(Note: Do not hang up the camera ﬁrmly until initial

installation test is completed). Plug adapter into wall outlet

and turn on the camera.

Step 2: Turn on monitor by pressing and holding Power /

Menu "

" button for 5 seconds until "KOEHOG" shows up,

then video will show up on the screen immediately. If video

does not show up, please refer to "TO PAIR MONITOR AND

CAMERA (ADD CAMERA)" at next page. If video shows up,

the initial installation test is completed, then you can set up

the camera according to the instruction below.

Set Up Camera: Place camera on a ﬂat surface, such as

wardrobe or shelf (Figure 1). Or hang it on the wall (Figure 2).

No matter wherever to place the camera, please make sure

to keep it away from the crib for at least 3 feet and all power

cords should be placed behind the camera properly. Then

adjust the angle of camera lens until the entire crib shows up

on the display, or adjust it to the best angle that you think to

watch your baby.

TO USE PLUGGED-IN MODE

Step 1: Place the monitor display in living room, bedroom or any place you want to watch your baby.

Use adapter to connect camera with electrical outlet.

POWER/VIDEO

Step 2: Turn on monitor by pressing

or video shows up on the screen.

POWER/VIDEO

Step 3: Press

" button to turn oﬀ the video if you only need to hear the voice.

Step 4: Turn oﬀ the monitor completely by pressing and holding

3 seconds.

TO USE PORTABLE/BATTERY MODE

Please charge the battery for 6 ~ 8 hours before using the product.

Step 1: Charge the battery for at least 6 hours before using portable / battery mode.

Step 2: Make sure the adapter is plugged into camera.

Step 3: The battery life can be up to 8 hours if it is fully charged.

Battery life will be shortened if recharging it continuously. Unplug the AC adapter when you are not

using it for a long time.

TO PAIR MONITOR AND CAMERA (ADD CAMERA)

The monitor and camera are paired before shipment. If it is unpaired for some reason, please refer

to the following steps:

Step 1: Make sure the camera and monitor are in the same space.

Step 2:

Step 3:

Step 4:

Step 5:

Red LED ﬂashs

The SCAN, SELECT, ADD, DELETE, VIEW CAMERA options are only available when

multiple cameras connected with the monitor. Order extra cameras by visiting

us at www.koehog.com or search "Axvue Baby monitor" on Amazon.

Figure 1

3 feet

Figure 2

" button for 3 seconds until "KOEHOG" logo

POWER/VIDEO

" button for

Make sure the AC adapter is plugged into

camera and turn on the camera by

pressing Power On/Oﬀ Switch "

button for 3 seconds.

Signal

Press