Architectural Mailboxes elephantrunk Montaj Talimatları

Çim ve Bahçe Ekipmanları Architectural Mailboxes elephantrunk için çevrimiçi göz atın veya pdf Montaj Talimatları indirin. Architectural Mailboxes elephantrunk 2 sayfaları. Parcel drop

Sayfayı Yazdır

elephantrunk

parcel drop

Carefully unpack the elephantrunk, parts and hardware.

Hardware and Parts (included)

x 1, mounting bolt

x 1, lag shield

(for hardscape

installation only)

x 1, handle

x 4, leveling feet

This address is equipped with an

elephantrunk

parcel drop

location:

x 2, keys

www.architecturalmailboxes.com

Architectural Mailboxes, LLC, 2012. Rev I

x 1, placard

x 1, cushion

x 1, outgoing partition

Choose where to locate your elephantrunk

NOTE: The elephantrunk parcel drop is NOT intended to replace a mailbox. Its primary

purpose is to receive parcel deliveries.

 The courier must be able to freely access your elephantrunk to make deliveries.

 Choose a protective location, such as on a porch or under an eave, and away from sprinklers.

 You can anchor your elephantrunk to a hardscaped or wooden surface. It will require drilling a hole into the surface, so make sure you

pick the right location.

elephantrunk installation

Place your elephantrunk at the desired location with

the help of another person.

Open the bottom

door and mark the

ground through the

hole in the floor.

After marking the ground, place the elephantrunk

aside before continuing.

Tools (not included)

x 1, washer

Drill suitable for drilling into masonry or wood

x 2, handle screws

Hex wrench

x 4, placard screws

- or -

Phillips head screwdriver

x 1, mounting knob

5/8" masonry drill bit

(if installing on hardscape)

1/4" wood drill bit

(if installing on wood deck/porch)

Drill a hole where you marked the ground:

For hardscape (for example, stone walkway or

concrete pad), drill a hole 2.5" deep at the mark with

a 5/8" masonry bit.

For wood (for example, deck or porch), drill a pilot

hole 2" deep at the mark using a 1/4" wood bit.

5/8" hole

For hardscape:

Remove any debris

from the hole and insert

the lag shield so it is

flush with the surface.

Screw the mounting bolt

into the lag shield.

Use the hex portion at the

center of the bolt to screw

it into the hole.

For both installations,

screw it all the way so the

hex portion is touching

the surface.

Carefully screw the four

leveling feet into the bottom

of each leg about half way.

elephantrunk use

1/4" hole

[email protected] with any questions.

For wood:

With help, lift the elephantrunk over the installed bolt,

Screw the

aligning the bolt through the hole in the floor. DO NOT

mounting bolt

secure in place with the mounting knob yet.

directly into the

Level the elephantrunk by adjusting the feet up

surface.

and down.

Place the washer over the bolt and screw on the

mounting knob. The knob only needs to be hand

tightened.

Place the cushion onto the floor over the mounting

knob.

Open the top door and attach the handle with the two

handle screws.

placard installation

Remove protective plastic coating from the placard.

Write the location of your elephantrunk onto the

placard with a permanent marker.

Attach the placard to your front entry in a conspicuous

location so the courier knows where to deliver your

items.

To activate your warranty, register your product at:

www.architecturalmailboxes.com/registration

Incoming drum can accept parcels up to

11.5" x 7.3" x 9.3".

Retrieve your parcels by unlocking the bottom door.

We're all ears!

Give us a call at (800) 464-7491 or email

Over tightening with a tool may damage

the floor and invalidate your warranty.

Swing down the "No Deliveries"

indicator to suspend deliveries.

Slide the outgoing

partition into the grooves

to trap your outgoing

parcel for future pickup.

Rev. A