Cisco 3845 - Security Bundle Router Hızlı Başlangıç Kılavuzu - Sayfa 14
Anahtar Cisco 3845 - Security Bundle Router için çevrimiçi göz atın veya pdf Hızlı Başlangıç Kılavuzu indirin. Cisco 3845 - Security Bundle Router 38 sayfaları. Integrated services routers
Ayrıca Cisco 3845 - Security Bundle Router için: Tescilli Olmayan Güvenlik Politikası (30 sayfalar), Sorun Giderme Kılavuzu (15 sayfalar), Hızlı Başlangıç Kılavuzu (40 sayfalar)
Sayfayı Yazdır
Use two screws for each side (supplied with the rack, not with the router).
Tip
Start the lower pair of screws first, and rest the brackets on the lower screws while you insert the upper pair of screws.
Attaching the Cable Management Bracket
The optional cable management bracket provides attachment points for organizing and routing cables. Attach the cable
management bracket to the left or right rack-mount bracket using the screw provided. You can attach the cable management
bracket to either the upper or the lower threaded hole. See Figure 9 for attachment locations.
Figure 9
Attaching the Cable Management Bracket to the Cisco 3825 Router
NM D-
ES W -
36
35x
GE 1
Fa stE the
10/ 100
rne t Po
/10 00
Bas e-T
x
17x
35x 17x
NM -
34x 16x
ES W -
33x 15x
15x
32x 14x
16
31x 13x
30x 12x
Fas tEt her
net Po rts
29x 11x
28x 10x
27x 9x
26x 8x
8x
7x
Ext
Pwr
-48 V
15x 7x
GE
14x 6x
10/ 100 /
13x 5x
12x 4x
100 0
11x 3x
Bas e-T
x
10x 2x
0x
EN
9x
1x
8x
0x
Grounding the Chassis
Warning
This equipment must be grounded. Never defeat the ground conductor or operate the equipment in the absence of
a suitably installed ground conductor. Contact the appropriate electrical inspection authority or an electrician if
you are uncertain that suitable grounding is available. Statement 1024
Warning
During this procedure, wear grounding wrist straps to avoid ESD damage to the card. Do not directly touch the
backplane with your hand or any metal tool, or you could shock yourself. Statement 94
You must connect the chassis to a reliable earth ground; the ground wire must be installed in accordance with local electrical
safety standards. For NEBS-compliant grounding, use size 6 AWG (13 mm
accessory kit.
This equipment is suitable for installation in Network Telecommunications Facilities and locations where the NEC
Note
applies. The equipment is suitable for installation as part of the Common Bonding Network (CBN).
To connect the chassis to a reliable earth ground, perform the following steps:
Strip one end of the ground wire to the length required for the ground lug or terminal (about 0.75 in. [20 mm] for the
Step 1
NEBS ground lug).
Step 2
Crimp the ground wire to the ground lug, using a crimp tool of the appropriate size.
14
rts
18x
Ext
Pwr
25x
-48 V
17
24x
GE 0
6x
23x
10/ 100
5x
/
22x
100 0
4x
21x 3x
Bas e-T
x
20x 2x
0x
EN
19x
1x
18x
0x
Cable management bracket.
Either edge may go up. Attach
to either side of the chassis.
2
) copper wire and the ground lug provided in the