Actulux SVM EI 24V-8A Kurulum Talimatı - Sayfa 7

Kontrol Paneli Actulux SVM EI 24V-8A için çevrimiçi göz atın veya pdf Kurulum Talimatı indirin. Actulux SVM EI 24V-8A 13 sayfaları. Control panel for fire ventilation

Sayfayı Yazdır

Control for Fire and Comfort Ventilation Type SVM EI 24V-5A / SVM EI 24V-8A

LEDs on main board and front panel

LED/colour

Symbol

Operation possibilities for:

LD1/red

Actuator open (red). Lights when actuator opens

LD2/green

Actuator close (green). Lights when actuator closes

LD3/red

Weather sensor active (red). Lights when weather sensor is active

LD4/red

Line error on actuator (red). Lights when actuator has open circuit,

flashes at earth fail or when short circuit occur.

It is not possible to RESET or close with actuator output (see page 7)

LD5/red

Line error on fire switch (red). Lights when fire switch has line error,

flashes when Fireman's Priority Switch has line error

LD6/red

Line error on smoke detector (red). Lights when smoke detector has

line error, flashes at temperatures above 75 °C

LD7/red

Bus error (red). Lights when BUS signal from other controls is

missing. Only relevant if J4-J7 is mounted.

Green

lights if everything is ok

Board + Front

switched off by local error on this control

flashes by error message from other controls received by bus

Yellow

Fault

Board + Front

lights by local error on this control

or by error message from other controls received by bus

*Yellow

Line error

Board + Front

flashes by local error on this control and if the ribbon cable or

jumper is not mounted on J9, or by error message from other

controls received by bus

AC error

*Yellow

Board + Front

flashes by local error on this control

or by error message from other controls received by bus

Alarm

Red

Board + Front

lights red constantly

*Yellow

DC error

Board + Front

flashes at normal speed (1 Hz) by local battery error on this control

or by error message from other controls received by bus

flashes at high speed (10 Hz) by battery voltage below 19V.

Reset by DIP 4: OFF/ON

Blue

Lights blue constantly in open condition (when windows are open)

Board + Front

flashes when actuator is moving up and down

Lights with*

Time for yearly service - please call for supplier (flashes fast)

Fuse specifications

24V

Placement

Fuse value

F1 8A fast ading fuse

1 pcs. for 24V motor output

Alarm/

Comfort

fire

operation

Yes

Only

Yes

Only

Yes

Only

Yes

Only

Yes

Only

Yes

Only

Yes

Control for Fire and Comfort Ventilation Type SVM EI 24V-5A / SVM EI 24V-8A

Complete jumper settings for SVM EI PCB

Text on board

Factory

Mounted / ON function

mounted

DIP 1

Conf. Fireswitch

Fire switch active from 500-3 KΩ.

A short circuit of the smoke detector

input will generate a line error

DIP 2

Failsafe

Line error on fire switch or detector

puts the control in alarm

DIP 3

Temp. Detekt

Line error on motor line

(upper resistor area) = alarm

DIP 4

Ser

Yes

Active

DIP 5

Snitch

LED's "remember" errors (line

errors, AC/Batt. error, bus error). The

LED's can only be switched off/reset

again by setting dip switch off

DIP 6

Fail Relay

Failure relay works as indication that

skylight is open

DIP 7

Week open

Weekly open (2 sec.) /close

(5 sec.) cycle activated

DIP 8

Option

Auto reset (see page 9)

DIP 9

Sprinkler

Motor output closes by active

detector (opens by activating the fire

switch)

DIP 10

Bus comfort

The control reacts on comfort signal

via bus activity

DIP 11

Bus fire

The control reacts on alarm signal

via bus activity

DIP 12

Lock-Out Mode

Slaves can enter Lock-Out Mode

see page 18

Yes

Internal Buzzer ON

1 - 2 - 3 - 4

Pos. 1

Connect according to number of

(motor)

27KΩ terminal resistors on actuator

Mot Mon act.

Yes

2 wire line monitoring via 27KΩ

terminal 2-3

(motor)

Ext Li Mon act.

3 wire line monitoring with direct

motor connection actuator

J4(Bus)

Start term.

First control panel in the bus network

J5(Bus)

+ Master

J6(Bus)

Slave

Middle and last control panel in the

bus network

J7(Bus)

End term.

Last control panel in the bus network

FOIL

Yes in Basic Line monotoring of front cabinet

J11

BatSup->Ø23

Battery backup of terminal 23

Others: Reset time = 180 sec. closing // Cut-off motor output and loading after 360 sec. // Comf. var (potetiometer): 1-60 sec.

Dismounted / OFF function

Fire switch active from 0-3 KΩ.

A short circuit of the smoke detector

input will generate alarm

Normal mode

Inactive

Normal mode

Normal mode (works as failure

relay)

Weekly open/close not activated

Normal mode

Normal mode - motor output opens

by ative detectors or fire switches

The control does not react on

comfort signals via bus activity //

NB! Always reaction on weather

signal and failures via bus activity

and own comfort signal

The control does not react on alarm

signal via bus activity

//NB! Always reaction on weather

signal and failures via bus activity

and own alarm signal (detector or

fire switch)

Normal mode

Internal Buzzer OFF

No line monitoring

See section concerning connection

of controls panels in bus connection,

page 14

Line error flashes

Terminal 23 only AC supplied