Epson L355 Buradan başlayın - Sayfa 2

Hepsi Bir Arada Yazıcı Epson L355 için çevrimiçi göz atın veya pdf Buradan başlayın indirin. Epson L355 2 sayfaları.
Ayrıca Epson L355 için: Buradan başlayın (2 sayfalar), Buradan başlayın (4 sayfalar), Buradan başlayın (2 sayfalar), Buradan başlayın (2 sayfalar), Buradan başlayın (2 sayfalar)

Sayfayı Yazdır
Epson L355 Buradan başlayın
Refilling Ink
To confirm the actual ink remaining,
Continued use of the product when
visually check the ink levels in the
the ink level is below the lower
product's ink tanks.
line on the tank could damage the
product.
Install the ink bottle cap tightly;
otherwise ink may leak.
Snap off, remove, and then install.
Install securely.
Repeat steps
to
for each
ink bottle.
Epson Ink
Color
Part numbers
Black
T6641
Cyan
T6642
Magenta
T6643
Yellow
T6644
Reading the Indication Lights
: flashing
The paper is jammed in the rear paper feed. Remove the jammed paper from the rear paper feed, load paper correctly, and press
No paper is loaded, or multiple sheets were fed at the same time. Load paper in the rear paper feed correctly and press
It is nearly time to reset the ink levels. Ink level may be low. You may continue printing. However, prepare new ink bottles soon. Epson
recommends the use of genuine Epson ink bottles. See the table in the "Refilling Ink" section for the ink bottle part numbers. To confirm the
actual ink remaining, visually check the ink levels in the product's ink tanks. Continued use of the product when the ink level is below the
lower line on the tank could damage the product.
It is time to reset the ink levels. Ink level may have reached the lower line. See the "Refilling Ink" section to fill all ink tanks with ink to clear
the error.
Fatal error. Turn the product off and then back on. If this does not clear the error, turn the product off and check inside the product for
jammed paper or foreign objects. For instructions on how to remove jammed paper, see the troubleshooting section of the online
User's Guide.
The product's ink pads are nearing or at the end of their service life. Contact Epson Support to replace ink pads. When the product's ink pads
are nearing the end of their service life, you can resume printing by pressing
An error occurred while establishing the Wi-Fi connection. Press
Network Guide.
The firmware update has failed. You will need to re-attempt the firmware update. Ready a USB cable and visit your local Epson website for
further instructions.
Getting More Information
You can see three online manuals. See the User's Guide (PDF file) for detailed
instructions on using the product.
Unhook.
Open and remove.
Refill the ink
up to the upper
line.
Close.
Hook onto.
Genuine Epson ink, other than those specified here, could cause
damage that is not covered by Epson's warranties.
: on
or
. The paper light and the ink light flash alternately.
to clear the error and try again. For more details, see the online
Guide to Control Panel
a
Network status light (green)
Install.
Turns the product on/off.
Starts monochrome or color copy. To increase the number of monochrome or color copies (by up to 20 copies),
press the same button within one second intervals. Press both buttons simultaneously to scan your original and
save it as PDF on your PC.
 Special Operations
If is on, press .
To perform print head cleaning, press for 3 seconds until the power light is flashing. The
cleaning uses some ink from all tanks, so run the cleaning only if quality declines like when you
see missing segments on your prints.
While pressing
, turn on the product to return the network settings to their
defaults.
Safety Instructions
or
.
Use only the power cord that
comes with the product. Use
or
.
of another cord may cause fire
or shock. Do not use the cord
with any other equipment.
Keep the product away from
direct sunlight or strong light.
Keep ink bottles and the ink
tank unit out of the reach of
children and do not drink
the ink.
Your product supports the Epson Connect service. This service allows you to print from your smartphone or tablet to your Epson
product.
b
c
Network status light (orange)
Power light
Establishes a Wi-Fi connection when pressed for 3 seconds.
While pressing , turn on the product to print the nozzle check
pattern shown below.
+
While pressing
Place the product near a wall
Use only the type of
Make sure the power cord
outlet where the power cord
power source indicated on
meets all relevant local
can be easily unplugged.
the product.
safety standards.
Do not open the scanner
Do not use aerosol products that contain
unit while copying, printing,
flammable gases inside or around the product.
or scanning.
Doing so may cause fire.
Do not tilt or shake an ink
Be sure to keep the ink bottles upright and
bottle after removing its seal;
do not subject them to impacts or temperature
this can cause leakage.
changes.
https://www.epsonconnect.com/
d
e
Ink light
Paper light
Prints a network status sheet.
Cancels the operation.
+
(a)
(a): OK.
(b): Needs a head cleaning.
(b)
+
or
, press within 3 seconds to copy in draft mode.
Do not let the power cord
become damaged or frayed.
Except as specifically explained in your
documentation, do not attempt to service the
product yourself.
If ink gets on your skin, wash the area
thoroughly with soap and water. If ink gets into
your eyes, flush them immediately with water. If
discomfort or vision problems continue after a
thorough flushing, see a doctor immediately. If
ink gets into your mouth, spit it out immediately
and see a doctor right away.