Cisco TelePresence Server 7010 Değiştirme Talimatları Kılavuzu - Sayfa 14
Ağ Donanımı Cisco TelePresence Server 7010 için çevrimiçi göz atın veya pdf Değiştirme Talimatları Kılavuzu indirin. Cisco TelePresence Server 7010 23 sayfaları. 600w ac-input power supply and fan tray replacement
Ayrıca Cisco TelePresence Server 7010 için: Kurulum Talimatları Kılavuzu (15 sayfalar), Kurulum Kılavuzu (14 sayfalar), Başlarken (16 sayfalar), Değiştirme Talimatları Kılavuzu (18 sayfalar)
Sayfayı Yazdır
Replacing the Chassis
Moving Processor Modules
At the interface processor end of the chassis, slots contain the processor modules. (See Figure 1 or
Figure 2.) In the Cisco 7010, the RP occupies the top slot (the RP slot or slot 4) and the SP (or SSP)
occupies the second slot from the top (the SP slot or slot 3), directly below the RP slot. The
remaining three slots, which are numbered 0 through 2 beginning at the bottom slot, support any
combination of interface processors.
In the Cisco 7505, the RSP1 occupies the top slot (slot 4). The remaining four slots, numbered 0
through 3 beginning at the bottom, support any combination of interface processors.
The processor modules are all keyed with guides on the backplane to prevent them from being fully
inserted in the wrong slot. Empty interface processor slots contain an interface processor filler (an
empty carrier) to help keep dust out of the chassis, provide EMI shielding, and maintain proper air
flow through the chassis interior.
Processor modules slide into the processor slots and connect directly to the backplane. The
spring-loaded ejector levers (see Figure 8) help to ensure that the bus connector on the back of the
processor module is fully seated in the backplane or fully dislodged from it. Captive installation
screws at both ends of each processor module faceplate prevent the processor from pulling away
from the backplane and support the EMI integrity of the system. Failure to use the ejector levers and
captive installation screws could result in a partial backplane connection, which can hang the system.
To retain your existing configuration, move interface processors to the same slot positions in the new
chassis. The lithium battery backup on the RP and RSP1 retains the system configuration and
MAC-layer addresses in nonvolatile random-access memory (NVRAM). Therefore, if you install
interface processors in the same slot positions in the new chassis that they occupied in the old
chassis, the system and the individual interfaces should come up in their previous configuration. If
you install interface processors in different slots in the new chassis, the system will recognize the
interfaces, but will leave them in a shutdown state until you reconfigure and enable them.
Although interface processors support OIR, you must wait at least 15 seconds after inserting an
interface processor before inserting the next one. To help avoid errors with the installation, leave the
power off until all components are moved into the new chassis and you have verified that all are
installed properly.
In the chassis, move the interface processors first, one at a time, then, in the Cisco 7010, move the
SP (or SSP) and finally the RP; in the Cisco 7505, move the RSP1 last. Before you remove an
interface processor from the existing chassis, remove the interface processor filler from the
corresponding slot in the new chassis. Then immediately install the interface processor in the new
chassis and secure it in the slot before removing the next interface processor filler or module. If you
leave the interface cables attached to the interface processors, route the cables through the cable
management brackets immediately after you secure the interface processor in the slot to help keep
the other slots clear during the installation.
If there is sufficient slack in the interface cables, and if you can easily move the processor modules
between the chassis without straining the cables, leave the interface cables connected. If you must
disconnect the cables, label each cable with its slot and port number before you disconnect it. Do not
reconnect the interface cables until you have installed all of the components in the new chassis (it is
easier to install interface processors when the slots are not impeded by cables that drop from other
slots). Use the optional cable management brackets to keep the interface cables untangled and away
from other interface processor slots and ports.
Caution
RSP1, all of which are required system components. Removing one while the system is operating
will cause the system to shut down or crash and might damage or destroy memory files.
14 Cisco 7010 and Cisco 7505 Chassis Replacement Instructions
You must turn off the system power before removing or installing the RP, SP (or SSP), or