Acuity Brands Lithonia Lighting D-Series Wall Kurulum Talimatları - Sayfa 3

Işık Fikstürü Acuity Brands Lithonia Lighting D-Series Wall için çevrimiçi göz atın veya pdf Kurulum Talimatları indirin. Acuity Brands Lithonia Lighting D-Series Wall 4 sayfaları. Size 1 led light fixture

Sayfayı Yazdır

Installation Instructions

D-Series Size 1 LED Wall

CAUTION: APPLY A CONTINUOUS BEAD OF WEATHER - PROOF CAULKING BETWEEN MOUNTING PLATE AND WALL TO ENSURE WEATHER - TIGHT

INTEGRITY OF ELECTRICAL COMPONENTS.

Tools Required: #2 philips type screwdriver, 1/4" hex driver. ELCW option also requires 11/32" closed end wrench.

Preparing the J-box for

D-Series Size 1 LED Wall

Remove one of the j-box screws. Loosen the remaining j-box screw. Remove the J-box adaptor strap from the supplied hardware bag and

position the strap keyhole over the loosened j-box screw. Align the remaining strap slot over the j-box screw mounting hole. Insert the j-

box screw and tighten. Tighten the remaining j-box screw. Remove the two screws from the supplied hardware bag and select holes on the

j-box strap that are as horizontally opposed as possible. Next you will need a ¼ hex driver. Do not tighten the screws all the way because

you will be mounting the back of the light fixture onto these screws.

Mounting the

D-Series Size 1 LED Wall

Loosen the light fixtures cover screws and unsnap the electrical connectors that connect the cover to the main fixture housing. Now place

the cover assembly aside until the last steps. Pull wires from the j-box in through the oblong wire access opening on the back of the main

fixture housing. Position the back of the fixture housing such that the two adaptor strap screw heads will fit through the keyhole slots in

the fixture housing. Now rotate the entire housing assembly until fixture is level. With a standard or small size ratchet and a ¼" hex driver,

tighten the two adaptor strap screws.

Take the cover assembly and snap the electrical connectors together with the main light fixture connectors. Place cover assembly back onto

the main light fixture housing taking care not to pinch any wires. Tighten the two cover closing screws with a Phillips style screwdriver.

Mounting the

D-Series Size 1 LED Wall

Loosen the light fixtures cover screws and unsnap the electrical connectors that connect the cover to the main fixture housing. Now place

the cover assembly aside until the last steps.

Take the main fixture housing and unsnap the two single electrical connectors that connect to the small fuseholder. Using an 11/32" closed

end wrench remove and save the two nuts that connect the main fixture housing to the emergency backbox. Remove the main fixture hous-

ing and pull the two single electrical connectors through the oblong wire access opening on the back of the main fixture housing. Pull the

remaining wires out of the emergency backbox through the emergency backbox cover wire access and unsnap the electrical connectors.

Now the main fixture housing can be set aside.

Take a Phillips style screwdriver and loosen the four screws on the back box cover assembly until the cover assembly can be removed from

the backbox. Unsnap the remaining electrical connections so that the cover assembly can be placed aside. Pull wires from the j-box in

through the oblong wire access opening on the back of the backbox. Position the back of the backbox such that the two adaptor strap

screw heads will fit through the keyhole slots in the fixture housing. Now rotate the backbox until it is level. With a ¼" hex driver, tighten

the two adaptor strap screws.

Take the backbox cover assembly and reconnect electrical connectors. The connectors that connect the backbox to the main fixture hous-

ing and the small fuseholder wires will need to be on the outside of the backbox cover wire access hole. Place the backbox cover assembly

onto the backbox and tighten the four screws. Take the two single electrical connectors that connect to the small fuseholder and feed them

back into the main housing. Take the remaining connectors coming from the back of the main housing and reconnect to the backbox con-

nectors. Place these connectors back through the backbox cover wire access opening. Now take the two nuts and tighten the main hous-

ing to the backbox cover. Reconnect the remaining connectors from the light fixture cover to the main housing.

Read the provided emergency instruction sheet (included in carton as a separate document) fully before making the last connection

which will be the connection of the small fuseholder/convertor.

Place light fixture cover assembly back onto main light fixture housing taking care not to pinch any wires. Tighten the two cover closing

screws with a Phillips style driver.

Installing D-Series Size 1 LED Wall

can be removed prior to assembly by snapping sections off.)

1. Remove the screws (2 for the DSXW1 & 4 for the DSXW2) that holds the light fixture electrical cover in place.

Then remove the cover assembly by disconnecting the quick disconnects. The spike assembly will be installed

using the provided self drilling screws.

2. Remove the paper backing from one side of the provided gasket and apply the gasket to the spike assembly.

3. Remove the paper backing from the remaining side of the gasket.

4. Select the spike assembly location so that the self drilling screws do not damage the fixture electricals.

5. Press the spike assembly onto your selected location and attach with the self drilling screws.

6. Snap the quick disconnects back together. Reinstall the cover taking care not to pinch any wires.

DELIVERY: Upon receipt of fixture and accessories (packed separately), thoroughly inspect for

any freight damage. All damage should be reported to the delivery carrier. Compare the catalog

description listed on the packing slip with the fixture label on the inside of the housing to be sure

you have received the correct merchandise.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two

conditions: (1) this device may not cause harmful interference, and (2) this device must accept

any interference received, including interference that may cause undesired operation.

fixture mounting:

standard fixture to a J-box:

ELCW fixture to a J-box:

Bird Spikes

(if the full length of the spike assembly is not desired, sections

Lithonia Lighting Outdoor • One Lithonia Way • Conyers, Georgia 30012

Phone: 800-279-8041 • Fax: 770.918.1209 •

5 year limited warranty

www.lithonia.com

Part Number:

RJ521349 Rev B

Revision Date: 6/3/14