Toshiba Carrier MMC-AP0181H2UL Kurulum Kılavuzu - Sayfa 12

Klima Toshiba Carrier MMC-AP0181H2UL için çevrimiçi göz atın veya pdf Kurulum Kılavuzu indirin. Toshiba Carrier MMC-AP0181H2UL 18 sayfaları. Air conditioner (multi type)

Sayfayı Yazdır

21-EN

Ceiling type

Applicable Controls

REQUIREMENT

• When this air conditioner is used for the first time, it

takes approx. 5 minutes until the remote control

becomes available after power-on. This is normal.

<When power is turned on for the first time after

installation>

It takes approx. 5 to 10 minutes until the remote

control becomes available.

Approx. 5 to 10 minutes

"SETTING"

Remote

Power

flashes

goes out

control is

available

<When power is turned on for the second (or later)

time>

It takes approx. 3 to 10 minute until the remote

control becomes available.

Approx. 3 to 10 minutes

"SETTING"

Remote

Power

flashes

goes out

control is

available

• Normal settings were made as factory default.

Change the indoor unit settings as required.

• Use the wired remote control to change the

settings.

* The settings cannot be changed using the

wireless remote control, simple wired remote

control, or central control system. Therefore,

install the wired remote control to change the

settings.

Installation Manual

Changing applicable control

setting

Basic procedure for changing settings

Change the settings while the air conditioner is not

working.

(Stop the air conditioner before making settings.)

Procedure

Push

button and temp. setup

button

simultaneously for 4 seconds or more.

After a while, the display flashes as shown in the figure.

Confirm that the CODE No. is [01].

• If the CODE No. is not [01], push

button to erase

the display content, and repeat the procedure from

the beginning.

(No operation of the remote control is accepted for a

while after

button is pushed.)

(While air conditioners are operated under the group

control, "

" is displayed first.

When

button is pushed, the indoor unit

number displayed following "ALL" is header unit.)

(* Display content varies with the

indoor unit model.)

Procedure

Each time

button is pushed, indoor unit

numbers in the control group change cyclically. Select

the indoor unit to change settings for.

The fan of the selected unit runs and the louvers start

swinging. The indoor unit can be confirmed for which to

change settings.

– 11 –

Ceiling type

Procedure

Specify CODE No. [

] with temp. setup

buttons.

Procedure

Select SET DATA [

] with timer time

buttons.

Procedure

Push

button. When the display changes from

flashing to lit, the setup is completed.

• To change settings of another indoor unit, repeat

from Procedure

• To change other settings of the selected indoor unit,

repeat from Procedure

Use

button to clear the settings.

To make settings after

button was pushed, repeat

from Procedure

Procedure

When settings have been completed, push

to determine the settings.

When

button is pushed, "SETTING" flashes and

then the display content disappears and the air

conditioner enters the normal stop mode.

(While "SETTING" is flashing, no operation of the

remote control is accepted.)

Installing indoor unit on high

ceiling

When the height of the ceiling to be installed exceeds

3.5 m (11'6"), adjustment of fan speed is necessary.

Set up the high ceiling.

• Set according to the basic operation procedure

→

(

• CODE No. in Procedure specifies [5d].

• Select [SET DATA] in Procedure from "List of

installable ceiling height" in this Manual.

• For the CODE No. in Procedure

, specify [5d].

• For the SET DATA in Procedure

, select the setup

data of high ceiling to be set up from the table on the

below.

(Exchange by wired remote control)

SET DATA

Standard

0000

11'6" (3.5 m) or less

(Factory default)

more than 11'6" (3.5 m)

0001

High ceiling 1

up to 13'1" (4.0 m)

Installation Manual

Remote control-less setting

To set the unit to high ceiling setting, there is a method

that requires the changing of the short plugs on the

indoor P.C. board. The details are shown in the below

table.

This method is only to be used where a wired remote

control (Group control) is not used.

* However, once the setting is changed, it is

necessary to reset the setting back to 0000 that

placing the short plugs back to the factory default

position and rewriting the setting data back to 0000

with wired remote control.

• Select by exchange of short plugs on indoor P.C.

board.

Short plug

position

SET DATA

button

Short

Open

Standard (Factory

0000

default)

0001

High ceiling 1

• Short plugs position (CN112, CN111, CN110 from

the left)

22-EN

Note