ARIS TENSOR I-ACT (PMR) Hızlı Kılavuz - Sayfa 2

Kontrolör ARIS TENSOR I-ACT (PMR) için çevrimiçi göz atın veya pdf Hızlı Kılavuz indirin. ARIS TENSOR I-ACT (PMR) 2 sayfaları.

Sayfayı Yazdır
ACTUATOR TENSOR I-ACT (PMR)
– Quick manual –
ATTENTION: Please observe the safety advices in the
original manual!
Stellantriebe
6
5
Top view I-ACT (PMR) (Cover opened)
D
1
C
B
 7-Segment-Display
 Sliding switch
 Adjustment buttons
 Operation condition LEDs
A
!
After rst switch-on
ADVICE
the display. Start the setting mode.
6
5
See original manual for more
!
ADVICE
adjustments and messages.
Setting mode I-ACT (PMR)
Set sliding switch  to position „MANU"
4
3
Hold down button „Menu"  > 2 sek.
2
4
Setting mode active, display  shows step 1
Change menu items
Display
Right
3
Menu
Left
Rohmasse
Material
Allgemeintoleranzen
ISO 2768-mk
ashes in
Massstab
Ind.
Name
Datum
Änderung
4
3
* only visible, if module is plugged in
scroll
down
2
1
D
Function
Remarks
Parameter
Set end position left 100%
no / yes
0...100%
Tensor S, 0% Tensor M
C
Set end position right 0%
no / yes
0...100%
Tensor S, 100% Tensor M
Set value input for left end
0/4/20/0...99
0...99 mA
position
0...5
0...5 V
0...10
0...10 V
Set value input for right end
0/4/20/0...99
0...99 mA
position
0...5
0...5 V
B
0...10
0...10 V
Actual value output left end
0/4/20/0...99
0...99 mA
position
0...5
0...5 V
0...10
0...10 V
Actual value output right end
0/4/20/0...99
0...99 mA
position
0...5
0...5 V
Mat.-Zustand / Behandlung
Bemerkungen / Lieferant
0...10
0...10 V
Projektion
Ersetzt durch
*
Ersatz für
Relay board
s. chapter 5.3.3
A
3D-Modell
KBD AddOn 03.iam
Gezeichnet
MA
31.03.2015
Geprüft
Alarm via fault message
0/1
0: inactive
Freigabe
output
1: active
Zeichnungsnummer
Index
KBD AddOn 03
2
1
Shut-off hysteresis
0...8, Hysteresis
0...80%
(b: brake)
for shut-off
Switch-on hysteresis
0...9, Hysteresis
0...90%
(d: difference)
for switch-on
RPM speed reduction
0...9
0...90%
prior to shut-off point
Firmware release
--
Actual rm-
ware no.
Exit, Switch to manual mode
--
scroll
confirm
up
entry
Programming of end positions, set value input and actual value output:
Activate setting mode
Approach end pos.
Save end pos.
Approach end pos.
Save end pos.
Choose values
0 mA 4 mA 20 mA X mA
Save value
Choose values
**
0 mA 4 mA 20 mA X mA
Save value
Choose values
**
0 mA 4 mA 20 mA X mA
Save value
Choose values
**
0 mA 4 mA 20 mA X mA
Save value
** Signaling analog to default set value
*