Whirlpool 3RLEC8600 Kurulum Talimatları Kılavuzu - Sayfa 8
Kurutucu Whirlpool 3RLEC8600 için çevrimiçi göz atın veya pdf Kurulum Talimatları Kılavuzu indirin. Whirlpool 3RLEC8600 8 sayfaları. Electric and gas dryers
Ayrıca Whirlpool 3RLEC8600 için: Kullanım ve Bakım Kılavuzu (12 sayfalar), Kurulum Talimatları Kılavuzu (8 sayfalar), Kurulum Talimatları Kılavuzu (8 sayfalar), Kullanım ve Bakım Kılavuzu (12 sayfalar)
Sayfayı Yazdır
Connect Vent
1. Connect vent to dryer outlet using 102 mm (4") clamp. If
connecting to existing vent, make sure the vent is clean. The
vent must t over the dryer outlet and inside the exhaust hood.
2. Move dryer into nal position. Do not crush or kink exhaust
vent. Make sure dryer is level.
Reverse Door Swing (Optional)
You can change your door swing from a right-side opening to a
left-side opening, if desired.
1. Place towel (A) on top of dryer to protect surface.
2. Open dryer door. Remove bottom screws from cabinet side of
hinges (B). Loosen (do not remove) top screws from cabinet
side of hinges.
3. Lift door until top screws in cabinet are in large part of hinge
slot. Pull door forward off screws. Set door (handle side up) on
top of dryer. Remove top screws from cabinet.
4. Remove screws attaching hinges to door.
5. Remove screws at top, bottom, and side of door (5 screws).
Holding door over towel on dryer, grasp sides of outer door
and gently lift to separate it from inner door. Do not pry apart
with putty knife. Do not pull on door seal or plastic door catch.
6. Be certain to keep cardboard spacer centered between doors.
Reattach outer door panel to inner door panel so handle is on
the side where hinges were just removed.
W10115523B
©
2009 Whirlpool Corporation.
All rights reserved.
A
B
®
Registered Trademark/TM Trademark of Whirlpool, U.S.A.
7. Attach door hinges to dryer door so that the larger hole is at
the bottom of the hinge.
8. Attach plugs to right side using the same 4 screws.
9. Insert screws into bottom holes on left side of cabinet. Tighten
screws halfway. Position door so large end of door hinge slot
is over screws. Slide door up so screws are in bottom of slot.
Tighten screws. Insert and tighten top screws in hinges.
10. Close door and check that door strike aligns with door catch.
If it is needed, slide door catch left or right within slot to
adjust alignment. Remove the 4 screws that attach 2 plugs
on the left side.
Complete Installation
1. Check to be sure all parts are now installed. If there is an
extra part, go back through the steps to see which step was
skipped.
2. Check to be sure you have all of your tools.
3. Properly dispose of all packaging materials.
4. Check the dryer's final location. Be sure the vent is not
crushed or kinked.
5. Check to be sure the dryer is level. See "Level the Dryer."
6. Read the Use & Care Guide to fully understand your new
dryer.
7. Select a full heat cycle (not the air cycle) and start dryer. After
five minutes, open dryer door. You should feel heat inside the
dryer or on the exhaust vent. If dryer makes an unusual noise,
check that the dryer is level.
Technical Specifications
(see rating plate in door opening for full model details)
220-240V ~ 50 Hz, 1 ph
4575W, IP24
Clothes capacity: 9.0 Kg max.
6/09
Printed in U.S.A.